HP Ink Tank 110 User Guide - Page 45

Tips for working with ink and printhead, Power

Get HP Ink Tank 110 PDF manuals and user guides View all HP Ink Tank 110 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Tips for working with ink and printhead Printhead tips Use the following tips to work with printheads: ● To protect the printheads from drying out, always turn the printer off using the Power button, and wait until the Power button light goes out. ● Do not open or untape printheads until you are ready to install them. Leaving tape on the printheads reduces ink evaporation. ● Insert the new printheads into the correct slots. Match the color and icon of each printhead to the color and icon for each slot. Make sure the printheads snap into place, and then close the printhead latch. After you have set up the printer, do not open the printhead latch unless instructed to do so. ● Align the printer for best print quality. See Printing issues on page 55 for more information. Ink tips Use the following tips to work with ink: ● Make sure the ink tanks are filled with ink and the ink levels are above the minimum line before printing. ● Refill the ink tanks when the ink level reaches the minimum line. Printing with the ink level below the minimum line may cause damage to your printer. ● Do not make the ink level be above the maximum line by overfilling the ink tanks or tilting the printer. The ink level higher than the maximum line can cause ink leaks and ink mixing. ENWW Tips for working with ink and printhead 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
Tips for working with ink and printhead
Printhead tips
Use the following tips to work with printheads:
●
To protect the printheads from drying out, always turn the printer
off
using the
Power
button, and wait
until the
Power
button light goes out.
●
Do not open or untape printheads until you are ready to install them. Leaving tape on the printheads
reduces ink evaporation.
●
Insert the new printheads into the correct slots. Match the color and icon of each printhead to the color
and icon for each slot. Make sure the printheads snap into place, and then close the printhead latch.
After you have set up the printer, do not open the printhead latch unless instructed to do so.
●
Align the printer for best print quality. See
Printing issues
on page
55
for more information.
Ink tips
Use the following tips to work with ink:
●
Make sure the ink tanks are
filled
with ink and the ink levels are above the minimum line before printing.
●
Refill
the ink tanks when the ink level reaches the minimum line. Printing with the ink level below the
minimum line may cause damage to your printer.
●
Do not make the ink level be above the maximum line by
overfilling
the ink tanks or tilting the printer.
The ink level higher than the maximum line can cause ink leaks and ink mixing.
ENWW
Tips for working with ink and printhead
41