HP Kayak XW A2-U2-W2 HP Kayak XW Series 04xx, Configuring a SCSI Accessory For - Page 5

Boot Device, Configuration Menu, SCSI Device

Page 5 highlights

HP Kayak XW 0480 PC Workstation - Configuring a SCSI Accessory Boot Device Configuration Menu This menu lets you configure the SCSI boot device. To find out the SCSI ID of a specific SCSI device, you can run the SCSI Disk Utilities (refer to page 8). Boot Device Configuration Select SCSI peripheral from which to boot To view peripheral by ID# select "SCSI Disk Utilities" from previous menu Boot SCSI ID 0 Option Listed Below Has NO EFFECT if MULTI LUN Support is Disabled Boot LUN Number 0 Use the and keys to move between options. Press to display a menu with a selection of values. • Boot SCSI ID This parameter is the SCSI ID of the boot device. The default value is 0. • Boot Lun Number More advanced SCSI devices can have several logical units. This option indicates the logical unit (or Lun) on which to boot for the drive chosen in the Boot SCSI ID. The default value is 0. SCSI Device Configuration Menu This menu lets you configure parameters for each SCSI device on the SCSI bus. To configure a specific SCSI device, you need to know which SCSI ID it uses. To know the SCSI ID of a specific SCSI device, you can run the SCSI Disk Utilities (refer to page 8). SCSI Device ID SCSI Device Configuration #0 #1 #2 #3 #4 #5 #6 #7 Initiate Sync Negotiation... yes yes yes yes yes yes yes yes Maximum Sync Transfer Rate.. 40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0 Enable Disconnection........ yes yes yes yes yes yes yes yes Initiate Wide Negotiation... yes yes yes yes yes yes yes yes Options Listed Below Have NO EFFECT if the BIOS is Disabled Send Start Unit Command.... no no no no no no no no BIOS Multiple LUN Support.. no no no no no no no no Include in BIOS Scan....... yes yes yes yes yes yes yes yes Use the and keys to move between options. Press to display a menu with a selection of values. • Initiate Sync Negotiation Some older SCSI-1 devices do not support synchronous negotiation. Set Initiate Sync Negotiation to No for these devices. English 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17

English
5
HP Kayak XW 0480 PC Workstation
— Configuring a SCSI Accessory
Boot Device
Configuration Menu
This menu lets you configure the SCSI boot device. To find out the
SCSI ID of a specific SCSI device, you can run the SCSI Disk Utilities
(refer to page 8).
Use the
and
keys to move between options. Press
to
display a menu with a selection of values.
Boot SCSI ID
This parameter is the SCSI ID of the boot device. The default value
is 0.
Boot Lun Number
More advanced SCSI devices can have several logical units. This
option indicates the logical unit (or Lun) on which to boot for the
drive chosen in the
Boot SCSI ID
. The default value is 0.
SCSI Device
Configuration Menu
This menu lets you configure parameters for each SCSI device on the
SCSI bus. To configure a specific SCSI device, you need to know which
SCSI ID it uses. To know the SCSI ID of a specific SCSI device, you can
run the SCSI Disk Utilities (refer to page 8).
Use the
and
keys to move between options. Press
to
display a menu with a selection of values.
Initiate Sync Negotiation
Some older SCSI-1 devices do not support synchronous negotiation.
Set Initiate Sync Negotiation to
No
for these devices.
Boot Device Configuration
Select SCSI peripheral from which to boot
To view peripheral by ID# select “SCSI Disk Utilities” from previous menu
Boot SCSI ID
.................................................
0
Option Listed Below Has NO EFFECT if MULTI LUN Support is Disabled
Boot LUN Number
..............................................
0
SCSI Device Configuration
SCSI Device ID
#0
#1
#2
#3
#4
#5
#6
#7
Initiate Sync Negotiation... yes
yes yes yes yes yes yes yes
Maximum Sync Transfer Rate.. 40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0
Enable Disconnection
........
yes yes yes yes yes yes yes yes
Initiate Wide Negotiation... yes
yes yes yes yes yes yes yes
Options Listed Below Have NO EFFECT if the BIOS is Disabled
Send Start Unit Command
....
no
no
no
no
no
no
no
no
BIOS Multiple LUN Support..
no
no
no
no
no
no
no
no
Include in BIOS Scan
.......
yes yes yes yes yes yes yes yes