HP Kayak XW U3-W3 HP Kayak PC Workstations, HP MaxiLife Hardware Monitoring
HP Kayak XW U3-W3 Manual
View all HP Kayak XW U3-W3 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Kayak XW U3-W3 manual content summary:
- HP Kayak XW U3-W3 | HP Kayak PC Workstations, HP MaxiLife Hardware Monitoring - Page 1
MaxiLife Hardware Monitoring Chip 1 - HP Kayak XW U3-W3 | HP Kayak PC Workstations, HP MaxiLife Hardware Monitoring - Page 2
'crisis' block. To do this, set the System board switch 10 to the Closed position. MaxiLife is partially replacing HP ASIC (Little Ben), and provides the necessary hardware monitoring control. However, MaxiLife is not accessible in I/O space or memory space of the system platform, but only through - HP Kayak XW U3-W3 | HP Kayak PC Workstations, HP MaxiLife Hardware Monitoring - Page 3
Chip MaxiLife Architecture The MaxiLife chip continuously monitors temperature and voltage sensors located in critical regions on the system board. This chip receives data about the various system components via a dedicated I2C bus, - HP Kayak XW U3-W3 | HP Kayak PC Workstations, HP MaxiLife Hardware Monitoring - Page 4
. If an error is detected, an error screen appears indicating the problem. Using MaxiLife When the Computer Is Powered Off NOTE For MaxiLife to (the LCD status panel will be blank), MaxiLife is still running and monitoring the state of the LCD buttons. From this state, the diagnostics program - HP Kayak XW U3-W3 | HP Kayak PC Workstations, HP MaxiLife Hardware Monitoring - Page 5
MaxiLife Hardware Monitoring Chip NOTE Diagnostics: Done FAIL Exit Diagnostics: Done OK Exit If no errors are detected, you can exit the test session, and the main power - HP Kayak XW U3-W3 | HP Kayak PC Workstations, HP MaxiLife Hardware Monitoring - Page 6
MaxiLife Hardware Monitoring Chip MaxiLife Test Sequence and Error Messages MaxiLife Test fan error when a cable is not connected). This type of error disappears dynamically when the problem has been fixed (for example, the fan cable has been reconnected). The different diagnostics are described - HP Kayak XW U3-W3 | HP Kayak PC Workstations, HP MaxiLife Hardware Monitoring - Page 7
MaxiLife Hardware Monitoring Chip MaxiLife Test Sequence and Error Messages Presence of CPUs or Terminators in the Processor Slots Error! CPU Socket Missing or incorrectly installed CPU or - HP Kayak XW U3-W3 | HP Kayak PC Workstations, HP MaxiLife Hardware Monitoring - Page 8
higher system, or when mixing Unbuffered and Registered memory modules. • Check that the video controller is correctly installed. Note: No error is detected if a monitor is not connected to an installed video controller. This is not a fatal error and the BIOS will continue its normal execution. 8 - HP Kayak XW U3-W3 | HP Kayak PC Workstations, HP MaxiLife Hardware Monitoring - Page 9
MaxiLife Hardware Monitoring Chip MaxiLife Test Sequence and Error Messages Post Test Sequence and Post Error Codes In order to check that the CPU is able to run the BIOS boot code (POST phase) from the first CPU instructions through to DIMM detection, MaxiLife firmware waits for a synchronization - HP Kayak XW U3-W3 | HP Kayak PC Workstations, HP MaxiLife Hardware Monitoring - Page 10
-Wide Web support page: http://www.hp.com/go/kayaksupport Operating System Boot Phase If no error message has been displayed at this stage of the system startup by the BIOS, the operating system is launched and the LCD status panel will display the system platform (for example, HP KAYAK XA-s), and - HP Kayak XW U3-W3 | HP Kayak PC Workstations, HP MaxiLife Hardware Monitoring - Page 11
MaxiLife Hardware Monitoring Chip MaxiLife Test Sequence and Error Messages • Pre-boot diagnostics. • Run- system's Serial EEPROM from a previously successful boot. This information includes: product name (HP Kayak XA-s), BIOS version, serial number, number of processors and speed, size of memory - HP Kayak XW U3-W3 | HP Kayak PC Workstations, HP MaxiLife Hardware Monitoring - Page 12
Monitoring Chip MaxiLife Test Sequence and Error Messages Boot Steps Diagnostics System Info strings in EEPROM Write BIOS DMI Table MaxiLife HP KAYAK mark. MaxiLife "Write "Write POST POST Code" BIOS ERROR" HP KAYAK XU POST Code 24 Error! POST XXXX Runs a set of diagnostics assessing - HP Kayak XW U3-W3 | HP Kayak PC Workstations, HP MaxiLife Hardware Monitoring - Page 13
MaxiLife Hardware Monitoring Chip MaxiLife Test Sequence and Error Messages selected, the main power supply is started but the PC is not allowed to do a normal boot. The - HP Kayak XW U3-W3 | HP Kayak PC Workstations, HP MaxiLife Hardware Monitoring - Page 14
MaxiLife Hardware Monitoring Chip MaxiLife Test Sequence and Error Messages Typical Diag Error Messages When message will indicate a BIOS error: The BIOS no longer works. There is no Flash. HP KAYAK XA-s Error! CPU Socket Error! Power CPU 1 Error! BIOS Error! Power CPU 1 Error! Power supply Error - HP Kayak XW U3-W3 | HP Kayak PC Workstations, HP MaxiLife Hardware Monitoring - Page 15
MaxiLife Hardware Monitoring Chip MaxiLife Test Sequence and Error Messages Table 4 The components More Information About MaxiLife Refer to the User's Guide delivered with the computer for more information about this diagnostics utility, or the HP Kayak XA-s, XU (Series 0301) and XW (Series U3 and - HP Kayak XW U3-W3 | HP Kayak PC Workstations, HP MaxiLife Hardware Monitoring - Page 16
MaxiLife Hardware Monitoring Chip MaxiLife Test Sequence and Error Messages 16
1
MaxiLife Hardware Monitoring Chip