HP LH4r HP Netserver LPr Technical Reference Card - Page 1
HP LH4r - NetServer - 256 MB RAM Manual
View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
HP 219239 BACK SIDE PN D9431-80204 6.181 X 11.811 DC 1682 ALA SP 85/2400 OM E Rear Panel PCI Slot #3 PCI Slot #2 PCI Slot #1 Management Port Link LED Network Activity LED 100 Mbps LED See LED definitions below Power Inlet Ultra SCSI Mouse Serial Port B Keyboard Serial Port A Monitor Parallel Port Rear Panel LED Definitions: Link Steady green when the LPr's network adapter and the network switch are properly connected and receiving power. Activity Rate of green flashes reflects network traffic to/from LPr's network adapter. 100 Mbps Steady green indicates support of 100 Mbps transfers. Off for 10 Mbps transfers. F Control Panel Power On/Off Reset Switch Drive Activity LED Switch Reset Drive Error LED Fan Failure LED Power On/Off LED Over-Temperature LED Control Panel LED Definitions: Power On/Off Steady green shows system power ON. Drive Activity Flashes green to show access over embedded SCSI controller. Drive Error OverTemperature Fan Failure Flashes red to indicate that one of the two drives in the hot-swap bays has failed and must be replaced. Remove front bezel to check drive LEDs. Flashes yellow to predict drive failure or to indicate that the drive is running out of space. Use TopTools to determine cause. Flashes red when temperature is hazardous -- shut down and check for sources of overtemperature. Flashes yellow when temperature nears hazardous levels - check for source of over-temperature. Flashes red to indicate a fan failure - shut down gracefully and replace the fan. Flashes yellow to indicate the start of a fan failure -- schedule shutdown and fan replacement. G Specifications Power Requirements Operating Current 100 VAC 5.3A 120 VAC 4.6A 200/208 VAC 3.2A 220/230 VAC 2.8A Voltage and Frequency 88 - 264VAC, 47-63Hz In-Rush Current 25A Leakage Current in Rack 15mA Delayed Action Circuit Breaker Recommendations 110/120 60Hz - NEMA AB1 Class 14B 220/240 50Hz - IEC Type C for 16A circuits Space Requirements System Dimensions 3.5"H x 17.6"W x 28"D (8.9cm x 44.7cm x 71.1cm) Rack Space 2 EIA units Rack Clearance None required System Weight 40 lbs (88 kg) Air Conditioning Requirements Maximum Heat Output 1041 BTU/hour Operating Temperature 41 to 95 degrees F (5 to 35 degrees C) Operating Humidity 20% to 80% RH H Memory • Use only HP DIMMs. • The LPr ships with 64MB and can support 1GB. • DIMMs may be installed in any combination in any socket. I Mass Storage • Two hot-swap SCSI drive shelves support LVDS low-profile SCSI devices. • Do not use HVD SCSI devices in the LPr. • Use single-ended SCSI devices on the SCSI bus outside of the LPr. • Be certain any external SCSI cable ends with proper termination and does not exceed 2.5 meters. HP NetServer LPr Service Information Electronic Support Services • Internet Web Page http://www.hp.com/go/netserver • Internet FTP ftp://ftp.netserver.hp.com • CompuServe Library GO HPPC • HP Navigator CD Support Questions • HP-Authorized Reseller • CompuServe Discussion Forum GO HPPC • US / Canada Phone Support 1-970-635-1000 • Europe Phone Support (+31-20) 581-3330 (Netherlands) HP has offices in over 100 countries. Check your local telephone directory. Selected HP Accessories For other tested accessories, download the Order Assistant from the HP Web page. Audience Assumptions This Service Reference Label is for trained service personnel. Hewlett-Packard Company assumes you are qualified in the servicing of computer equipment and trained in recognizing hazards in products with hazardous energy levels. Electrostatic Discharge To avoid catastrophic or hidden damage to components, wear a wrist strap and use a staticdissipative work surface connected to the chassis when handling components. Use an antistatic service kit, such as 3M® 8501/8502/8505 or equivalent. System Troubleshooting • Check LEDs at front and rear of system as shown in panels at left. • On power-up, a beep error code message may appear before the video display starts. Refer to the list of Beep Codes in Information Assistant on your LPr On-Line Documentation CD. • If an error code appears during boot, place the HP Network Navigator CD in the CD-ROM drive, attempt the boot and then press the ENTER key when the error code appears. An explanation will appear on the screen. • Check that the System Board is properly seated in the I/O Board. Interrupt Sharing • Note that the embedded SCSI Controller and PCI Slot #3 share the same interrupt line. The operating system will distinguish the interrupt source, but performance will be adversely affected. This information is subject to change without notice and is provided without warranty. ©2000, Hewlett-Packard Company. All rights reserved. P/N: D9431-80204 For additional information, see other side.