HP Mini 210-2070nr HP Mini 2102, HP Mini 210, and Compaq Mini 210 - Maintenanc - Page 51

Hard drive, Disconnect the hard drive cable

Get HP Mini 210-2070nr PDF manuals and user guides View all HP Mini 210-2070nr manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

3. Swing the rear edge of the service cover (1) back and down, and then firmly press down on the cover (2) so the clips on the cover access the slots on the base enclosure. Hard drive NOTE: Each hard drive spare part kit includes a cable adapter, bracket, and four rubber isolators. Description Hard drive: 320-GB, 7200-RPM 250-GB, 7200-RPM, WWAN 160-GB, 7200-RPM, WWAN Hard Drive Hardware Kit Spare part number 590819-001 599665-001 599666-001 589673-001 Before removing a hard drive, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer. 4. Remove the battery (see Battery on page 38). 5. Remove the service cover (see Battery on page 38). Remove the hard drive: 1. Disconnect the hard drive cable (1) from the system board. 2. Use the Mylar tab (2) on the right side of the hard drive to lift the right side of the drive (3) until it rests at an angle. Component replacement procedures 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
3.
Swing the rear edge of the service cover
(1)
back and down, and then firmly press down on the
cover
(2)
so the clips on the cover access the slots on the base enclosure.
Hard drive
NOTE:
Each hard drive spare part kit includes a cable adapter, bracket, and four rubber isolators.
Description
Spare part number
Hard drive:
320-GB, 7200-RPM
590819-001
250-GB, 7200-RPM, WWAN
599665-001
160-GB, 7200-RPM, WWAN
599666-001
Hard Drive Hardware Kit
589673-001
Before removing a hard drive, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see
Battery
on page
38
).
5.
Remove the service cover (see
Battery
on page
38
).
Remove the hard drive:
1.
Disconnect the hard drive cable
(1)
from the system board.
2.
Use the Mylar tab
(2)
on the right side of the hard drive to lift the right side of the drive
(3)
until it
rests at an angle.
Component replacement procedures
43