HP OmniBook 7150 HP OmniBook 2100 - Memory Installation Sheet - Page 1
HP OmniBook 7150 - Notebook PC Manual
View all HP OmniBook 7150 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
RAM Expansion Module Important: If you are installing a RAM module in a Pentium I computer with two memory expansion slots, up to 32MB memory is supported in slot 2 (the slot closest to the corner of the computer). Caution: Static electricity can permanently damage computer chips. To avoid damaging your RAM expansion module: • Discharge your body's electricty by touching the metal shielding around the connectors on the rear of the OmniBook computer. • Handle the RAM expansion module only by its edges. To install the RAM expansion module 1 Click the Start Button and select Shut down. 2 Unplug the ac adapter, if present, and remove all batteries. 3 Remove the RAM expansion cover located on the bottom of the OmniBook. 4 Insert the RAM expansion module into the connector at about a 30° angle until it's fully inserted. Then press down at both sides of the module until it latches. 5 Snap the RAM expansion module door back into place. 6 Insert the battery. To remove the RAM expansion module After you remove the RAM expansion module door, do the following: 1 Release the two metal latches at the sides of the RAM expansion module by pushing them outward (away from the sides of the module). When you release the latches, the free edge of the module pops up. 2 Pull the module out of the connector. See the printed Reference Guide provided with your OmniBook for more information about replacing a RAM expansion module. RAM Expansion Module ® Multilingual Printed in France 1 2 3 4 5 6 7 8 9 10 11 12 94 95 96 97 98 99 Part Number (P) 5967-4742 Edition 1 RAM-Erweiterungsmodul Wichtig: Wenn Sie ein RAM-Modul in einem Pentium I Computer mit zwei Speichererweiterungssteckplätzen einbauen, werden in Steckplatz 2 (dem Steckplatz, der der Ecke des Computers am nächsten liegt) bis zu 32 MB unterstützt. Achtung: Durch statische Elektrizität können Computer-Chips beschädigt werden. Beachten Sie daher folgende Hinweise, um Schäden an Ihrem RAM-Erweiterungsmodul vorzubeugen: • Berühren Sie die Metallblenden an den Anschlüssen an der Rückseite des Omnibook Rechners, um körpereigene Spannung abzuleiten. • Fassen Sie das RAM-Erweiterungsmodul nur an den Kanten an. Einsetzen des RAM-Erweiterungsmoduls 1 Fahren Sie den OmniBook Rechner über das Menü Start herunter. 2 Ziehen Sie ggf. den Netzadapter ab, und entfernen Sie alle Akkus. 3 Entfernen Sie die Abdeckung der RAM-Erweiterung auf der Unterseite des OmniBook Notebook PCs. 4 Führen Sie das RAM- Erweiterungsmodul vollständig in einem Winkel von 30° ein. Drücken Sie dann das Modul an beiden Seiten herunter, bis es fest verriegelt ist. 5 Bringen Sie die Abdeckklappe für das RAM-Erweiterungsmodul wieder in ihre Ausgangsposition. 6 Setzen Sie den Akku wieder ein. Herausnehmen des RAM-Erweiterungsmoduls Gehen Sie nach Entfernen der Abdeckklappe für das RAMErweiterungsmodul wie folgt vor: 1 Lösen Sie die beiden Metallklammern an den Kanten des RAMErweiterungsmoduls. Drücken Sie dazu die Klammern nach außen (von den Modulkanten weg). Sobald Sie die Klammern loslassen, springt die freie Kante des Moduls heraus. 2 Ziehen Sie das Modul aus dem Anschluß heraus. Weitere Informationen zum Einsetzen und Herausnehmen des RAMErweiterungsmoduls finden Sie im Referenzhandbuch, das zusammen mit Ihrem OmniBook Rechner ausgeliefert wird. Módulo de Expansión de RAM Importante: Si va a instalar un módulo de RAM en un PC Pentium I con dos ranuras de expansión de memoria, tenga en cuenta que la ranura 2 (la ranura más próxima a la esquina del PC) soporta un máximo de 32MB de memoria. Precaución: La electricidad estática puede dañar de forma permanente los chips del computador. Para evitar que se dañe el módulo de expansión de RAM: • Descargue la electricidad de su cuerpo tocando la protección metálica que hay alrededor de los conectores de la parte posterior del computador OmniBook. • Manipule el módulo de expansión de RAM sólo por sus extremos. Cómo instalar el módulo de expansión de RAM 1 Haga clic en el menú Inicio y seleccione Apagar el sistema. 2 Desenchufe el adaptador de ca, si está enchufado, y saque todas las baterías. 3 Estraiga la cubierta de ampliación de RAM que se encuentra en la parte inferior del OmniBook. 4 Inserte el módulo de expansión de RAM en el conector a un ángulo de unos 30º hasta que esté perfectamente colocado. A continuación, presione sobre ambos lados del módulo hasta que éste quede enganchado. 5 Vuelva a ajustar la puerta del módulo de expansión de RAM en su lugar. 6 Inserte la batería. Cómo sacar el módulo de expansión de RAM Después de retirar la puerta del módulo de expansión de RAM, haga lo siguiente: 1 Libere los dos enganches metálicos que hay a ambos lados del módulo de expansión de RAM empujándolos hacia afuera (separándolos de los lados del módulo). Cuando libere los enganches, se alzará el borde libre del módulo. 2 Tire del módulo para extraerlo del conector. En la Guía de Consulta impresa que acompaña al OmniBook encontrará más información sobre cómo instalar y retirar RAM del OmniBook.