HP OmniBook XE2-DE HP OmniBook XE Series - Modem AT Commands
HP OmniBook XE2-DE - Notebook PC Manual
 |
View all HP OmniBook XE2-DE manuals
Add to My Manuals
Save this manual to your list of manuals |
HP OmniBook XE2-DE manual content summary:
- HP OmniBook XE2-DE | HP OmniBook XE Series - Modem AT Commands - Page 1
AT Commands Basic AT Commands Command Function A/ Re-execute command Command A B0 Select V.22 connect @1200 bps B1 C1 Return OK message Dn E0 Turn off command echo E1 H0 Initiate a hang-up sequence H1 I0 Report product code I1 Report pre-computed checksum I2 I3 Report - HP OmniBook XE2-DE | HP OmniBook XE Series - Modem AT Commands - Page 2
RDL without self-test &T7 Request an RDL with self-test &T8 Initiate local analog loop with self- &V Display current configuration and stored test profiles &V1 Display last connection statistics &W0 Store the current configuration as &W1 Store the current configuration as profile 0 profile - HP OmniBook XE2-DE | HP OmniBook XE Series - Modem AT Commands - Page 3
Video Ready mode **0 Download to flash memory at last **1 Download to flash memory at 38.4 kbps sensed speed **2 Download to flash memory level> 0 to 30 (0 dBm to -30 dBm) FAX Class 1 +Fclass=1 Service class +FAE=1 Enable data/fax auto answer +FRM=n Receive data +FTH=n Transmit data - HP OmniBook XE2-DE | HP OmniBook XE Series - Modem AT Commands - Page 4
0 USA 1 Japan 2 Germany 3 UK(CTR-21) 4 France 5 Austria 6 Italy 7 Australia 8 Sweden 9 Denmark 10 New Zealand 11 Korea 12 China 13 Singapore 14 Malaysia 15 South Africa 16 Poland 17 Czechoslovakia 18 Hungary 19 Hong Kong 20 Turkey 21 Spain %Tn PTT Testing - HP OmniBook XE2-DE | HP OmniBook XE Series - Modem AT Commands - Page 5
%TT48 V.17 9600 bps short train %TT49 V.17 12000 bps long train %TT4A V.17 12000 bps short train %TT4B V.17 14400 bps long train %TT4C V.17 14400 bps short train %TT60 2400 bps ( V.34 only ) %TT61 4800 bps ( V.34 only ) %TT62 7200 bps (V.34 only ) %TT63 9600 bps (V.34 only ) %TT64 12000 bps (V.34 - HP OmniBook XE2-DE | HP OmniBook XE Series - Modem AT Commands - Page 6
S-Registers Register Function S0 Rings to auto-answer S1 Ring counter S2 Escape character S3 Carriage return character S4 Line feed character S5 Backspace character S6 Wait time for dial tone S7 Wait time for carrier S8 Pause time for dial delay modifier S9 Carrier detect response time S10 Carrier - HP OmniBook XE2-DE | HP OmniBook XE Series - Modem AT Commands - Page 7
Result Code Summary OK 0 RING 2 ERROR 4 NO DIAL TONE 6 NO ANSWER 8 CONNECT 2400 10 CONNECT 9600 12 CONNECT 12000 14 CONNECT 19200 16 CONNECT 57600 18 CONNECT 230400 20 CONNECT 1200TX/75RX 23 BLACKLISTED 32 DATA 35 CARRIER 1200/75 44 CARRIER 1200 46 CARRIER 4800 48
-
1 -
2 -
3 -
4 -
5 -
6 -
7
 |
 |
AT Commands
Basic AT Commands
Command
Function
Command
Function
A/
Re-execute command
A
Go off-hook and attempt to answer a call
B0
Select V.22 connect @1200 bps
B1
Select Bell 212A connect @1200 bps
C1
Return OK message
Dn
Dial modifier
E0
Turn off command echo
E1
Turn on command echo
H0
Initiate a hang-up sequence
H1
If on-hook, go off-hook and enter
I0
Report product code
command mode
I1
Report pre-computed checksum
I2
Report “OK” if the calculated checksum
I3
Report firmware revision, model,
equals the prestored checksum or if the
and interface type
prestored checksum value is FFh
I4
Report response programmed by OEM I5
Report the country code parameter
I6
Report modem data pump model
I7
Report the DAA code
and code revision
L0
Set low speaker volume
L1
Set low speaker volume
L2
Set medium speaker volume
L3
Set high speaker volume
M0
Turn speaker off
M1
Turn speaker on during handshaking
M2
Turn speaker on during handshaking and
and turn speaker off while receiving
while receiving carrier
carrier
M3
Turn speaker off during dialing and
N0
Turn off automode detection
receiving carrier and turn speaker on
N1
Turn on automode detection
during answering
O0
Go on-line
O1
Go on-line and initiate a retrain sequence
P
Force pulse dialing
Q0
Allow result codes to DTE
Q1
Inhibit result codes to DTE
Sn
Select S-Register n as default
Sn?
Return the value of S-Register n
Sn=v
Set default S-Register n to value v
T
Force DTMF dialing
V0
Report short form result codes
V1
Report long form result codes
W0
Report DTE speed only
W1
Report line speed, EC protocol and DTE
W2
Report DCE speed only
speed
X0
Report basic call progress result codes,
X1
Report basic call progress result codes
i.
e., Ok, Connect, Ring, No Carrier
and connections speeds (Ok, Connect,
(also, for busy, if enabled, and dial tone
Ring, No Carrier (also, for busy, if
not detected), No Answer and Error
enabled, and dial tone not detected), No
X2
Report basic call progress result codes
Answer, Connect XXXX, and Error
and connections speeds, i.e., Ok,
X3
Report basic call progress result codes
Connect, Ring, No Carrier (also, for
and connections rate, i.e., Ok, Connect,
busy, if enabled, and dial tone not
Ring, No Carrier, No Answer, Connect
detected), No Answer, Connect XXXX,
XXXX, Busy, and Error
and Error
Y0
Disable long space disconnect before on-
X4
Report all call progress result codes
hook
and connections rate, i.e., Ok, Connect, Y1
Enable long space disconnect before on-
Ring, No Carrier, No Answer, Connect
hook
XXXX, Busy, No Dial Tone and Error
Z0
Restore stored profile 0 after warm reset
Z1
Soft reset and restore stored profile 1
&C0
Soft reset and force RLSD active
after warm reset
regardless of the carrier state
&C1
Allow RLSD to follow the carrier state
&D0
Interpret DTR On-to-OFF transition
&D1
Interpret DTR On-to-OFF transition
per &Qn
per &Qn
&Q0, &Q5, &Q6
The modem ignores DTR
&Q0, &Q1, &Q4, &Q5, &Q6 Asynchronous escape
&Q1, &Q4
The modem hangs up
&Q2, &Q3
The modem hangs up
&Q2, &Q3
The modem hangs up
&D2
Interpret DTR On-to-OFF transition
&D1
Interpret DTR On-to-OFF transition
per &Qn
per &Qn
&Q0 through &Q6
The modem hangs up
&Q0, &Q1, &Q4, &Q5, &Q6
Soft reset
&Q2, &Q3
The modem hangs up
Note:
Bold face indicates default value
&F0
Restore factory configuration 0
&F1
Restore factory configuration 1