HP P2000 HP P2000 3.5-inch Large Form Factor Drive Enclosure I/O Module Firmwa - Page 6

Installing firmware using FTP, Supersedes history - specifications

Get HP P2000 PDF manuals and user guides View all HP P2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

8. Click Install Expansion-Module Firmware File. Wait for progress messages to specify that the update is complete. 9. In the SMU display, verify that the proper firmware version appears for each module. Installing firmware using FTP 1. Place the downloaded firmware package in a temporary directory. 2. If using a Smart Component, extract the contents of the Smart Component. In Windows - Click Extract on the first screen of the Smart Component. In Linux - Enter ./CPxxxxxx.scexe --unpack= to extract the contents of the Smart Component to the folder. For example,./CP123456.scexe -unpack=extract_here 3. Locate the firmware file in the downloaded/extracted folder. The firmware file name is in the following format: S110Bxx.bin 4. Do one of the following: • To update all modules, proceed to step 5. • To update specific modules, do the following to determine the address of each module to update: In the CLI, display the addresses by entering the show enclosures command. The needed data is displayed in the columns labeled EMP A CH:ID Rev and EMP B CH:ID Rev. 5. Using the SMU, prepare to use FTP: a. Determine the network-port IP addresses of the system controllers. b. Verify that the system FTP service is enabled. c. Verify that the user you will log in as has permission to use the FTP interface and has manage access rights. 6. In single-domain environments, stop I/O to the vdisks before starting the firmware update. 7. Open a command prompt (Windows) or a terminal window (UNIX), and navigate to the directory containing the firmware file to load. a. Enter ftp . (For example: ftp 10.1.0.9) b. Log in as an FTP user (user = ftp, password = !ftp). c. Enter one of the following commands: • To update all detected modules, enter: put encl flash. For example: put S110Bxx.bin encl flash • To update a specific module, enter: put encl:: flash. For example: put S1xxBxx.bin encl:0:15 flash 8. If needed, repeat these steps to load the firmware on additional modules. 9. Quit the FTP session. 10. In the SMU display, verify that the proper firmware version appears for each module. Supersedes history Firmware version S110B23 S100B56 S100B52 Release date June 2011 January 2011 June 2010 6 Supersedes history

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
8.
Click
Install Expansion-Module Firmware File
.
Wait for progress messages to specify that the update is complete.
9.
In the SMU display, verify that the proper firmware version appears for each module.
Installing firmware using FTP
1.
Place the downloaded firmware package in a temporary directory.
2.
If using a Smart Component,
extract the contents of the Smart Component.
In Windows — Click
Extract
on the first screen of the Smart Component.
In Linux — Enter
./CPxxxxxx.scexe --unpack=<folder name>
to extract the contents of
the Smart Component to the
<folder name>
folder. For example,
./CP123456.scexe
–
unpack=extract_here
3.
Locate the firmware file in the downloaded/extracted folder. The firmware file name is in the
following format:
S110Bxx.bin
4.
Do one of the following:
•
To update all modules, proceed to step 5.
•
To update specific modules, do the following to determine the address of each module to
update:
In the CLI, display the addresses by entering the
show enclosures
command. The needed
data is displayed in the columns labeled
EMP A CH:ID Rev
and
EMP B CH:ID Rev
.
5.
Using the SMU, prepare to use FTP:
a.
Determine the network-port IP addresses of the system controllers.
b.
Verify that the system FTP service is enabled.
c.
Verify that the user you will log in as has permission to use the FTP interface and has manage
access rights.
6.
In single-domain environments, stop I/O to the vdisks before starting the firmware update.
7.
Open a command prompt (Windows) or a terminal window (UNIX), and navigate to the directory
containing the firmware file to load.
a.
Enter
ftp <controller-network-address>
. (For example:
ftp 10.1.0.9
)
b.
Log in as an FTP user (user =
ftp
, password =
!ftp
).
c.
Enter one of the following commands:
•
To update all detected modules, enter:
put <firmware-file> encl flash
. For
example:
put S110Bxx.bin encl flash
•
To update a specific module, enter:
put <firmware-file>
encl:<channel-ID>:<EMP-number> flash
. For example:
put S1xxBxx.bin
encl:0:15 flash
8.
If needed, repeat these steps to load the firmware on additional modules.
9.
Quit the FTP session.
10. In the SMU display, verify that the proper firmware version appears for each module.
Supersedes history
Release date
Firmware version
June 2011
S110B23
January2011
S100B56
June 2010
S100B52
6
Supersedes history