HP P2000 HP P2000 G3 1GbE iSCSI MSA and 10GbE iSCSI MSA Controller Firmware TS - Page 6

Abort Verify Vdisk, Add Remote System - configuration

Get HP P2000 PDF manuals and user guides View all HP P2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

◦ If a partner controller is restarted during replication, settings in the Scheduler will now be maintained; no extraneous replication images will be created. ◦ Replication schedules will no longer cause the SMU to time out and become unresponsive. ◦ Improved the messaging when attempting to detach a secondary replication volume and an initial replication has not occurred. ◦ When creating replication sets, if network settings are configured incorrectly, the correct error message will now be displayed. ◦ Snapshot sync points will now be displayed correctly. ◦ No snapshots will be taken after the schedule has expired. ◦ The controller will no longer hang when trying to add an invalid Remote Snap destination-volume. • The following fixes are specific to the Storage Management Utility (SMU): ◦ The Provisioning wizard will now permit a vdisk to be created with 128 volumes. ◦ On the Add Remote System page, the Password field could be left blank. A valid entry is now required. ◦ Reworded the message displayed for the Rename Host task. ◦ Online help was updated to reflect that no progress bar or message will be displayed when a roll back is in progress. ◦ Single-ported SATA drives installed in cascaded HP D2700 drive enclosures will now show the correct status information; they will no longer be displayed as "degraded". ◦ Corrected name and fan information displayed for D2700 drive enclosures. ◦ When running the Verify Vdisk utility, the Abort Verify Vdisk button will no longer be grayed-out. • The following fixes are specific to the Command Line Interface (CLI): ◦ For scripted CLI, removed an issue that caused the controller to crash and generate communication errors. ◦ set cache-parameters command: If the command syntax is correct, the "An invalid device was specified" message will no longer be displayed. ◦ create vdisk command: The assigned-to parameter will now be ignored when in single-controller mode. ◦ set cli-parameters command: Will now be recorded in the specified locale language, not the previous locale language. ◦ set cli-parameters and show cli-parameters commands: Corrected wording inconsistency in the online help. ◦ create volume-set command: Updated online help. ◦ vdisk shutdown command: A vdisk that has been stopped will now display the Status as STOP, and the Health as Unknown. ◦ set advanced settings command: The following parameter settings are now recognized: enable, enabled, disable, and disabled. ◦ show controllers command: Corrected the display to remove the possibility of a rare display of an unclear error message. ◦ show replication-volumes command: Corrected the display. ◦ create user command: If conflicting base and storage-size-base parameters are both set, an error message will now be displayed. 6 Fixes

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
◦
If a partner controller is restarted during replication, settings in the Scheduler will now be
maintained; no extraneous replication images will be created.
◦
Replication schedules will no longer cause the SMU to time out and become unresponsive.
◦
Improved the messaging when attempting to detach a secondary replication volume and an
initial replication has not occurred.
◦
When creating replication sets, if network settings are configured incorrectly, the correct
error message will now be displayed.
◦
Snapshot sync points will now be displayed correctly.
◦
No snapshots will be taken after the schedule has expired.
◦
The controller will no longer hang when trying to add an invalid Remote Snap
destination-volume.
•
The following fixes are specific to the Storage Management Utility (SMU):
The Provisioning wizard will now permit a vdisk to be created with 128 volumes.
◦
◦
On the
Add Remote System
page, the
Password
field could be left blank. A valid entry is
now required.
◦
Reworded the message displayed for the
Rename Host
task.
◦
Online help was updated to reflect that no progress bar or message will be displayed when
a roll back is in progress.
◦
Single-ported SATA drives installed in cascaded HP D2700 drive enclosures will now show
the correct status information; they will no longer be displayed as “degraded”.
◦
Corrected name and fan information displayed for D2700 drive enclosures.
◦
When running the
Verify Vdisk
utility, the
Abort Verify Vdisk
button will no longer be
grayed-out.
•
The following fixes are specific to the Command Line Interface (CLI):
For scripted CLI, removed an issue that caused the controller to crash and generate
communication errors.
◦
◦
set cache-parameters
command: If the command syntax is correct, the “An invalid
device was specified” message will no longer be displayed.
◦
create vdisk
command: The
assigned-to
parameter will now be ignored when in
single-controller mode.
◦
set cli-parameters
command: Will now be recorded in the specified locale language,
not the previous locale language.
◦
set cli-parameters
and
show cli-parameters
commands: Corrected wording
inconsistency in the online help.
◦
create volume-set
command: Updated online help.
◦
vdisk shutdown
command: A vdisk that has been stopped will now display the Status as
STOP
, and the Health as
Unknown
.
◦
set advanced settings
command: The following parameter settings are now recognized:
enable
,
enabled
,
disable
, and
disabled
.
◦
show controllers
command: Corrected the display to remove the possibility of a rare
display of an unclear error message.
◦
show replication-volumes
command: Corrected the display.
◦
create user
command: If conflicting
base
and
storage-size-base
parameters are
both set, an error message will now be displayed.
6
Fixes