HP P4000 HP StorageWorks P4000 10GbE SFP+ Hardware Installation Instructions (
HP P4000 Manual
 |
View all HP P4000 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP P4000 manual content summary:
- HP P4000 | HP StorageWorks P4000 10GbE SFP+ Hardware Installation Instructions ( - Page 1
a management group Install hardware using the HP StorageWorks P4000 10GbE SFP+ Hardware Installation Instructions Download the HP StorageWorks P4000 G1 Series 1GbE to 10GbE SFP+ Migration Guide. Follow instructions in the Migration Guide for planning the upgrade. Open the CMC and install software - HP P4000 | HP StorageWorks P4000 10GbE SFP+ Hardware Installation Instructions ( - Page 2
HP StorageWorks P4000 10G BASE-SFP+ Upgrade Kit, which includes: • HP NC550SFP Dual Port 10GbE • 2GB Reg PC2-5300 2x1GB Kit • Software patch 10073 To install the hardware 1. Locate the torx tool on the back of the unit and loosen the cover screw. 7. Install straight up. 10. Install the riser - HP P4000 | HP StorageWorks P4000 10GbE SFP+ Hardware Installation Instructions ( - Page 3
SAN/iQ software Upgrading HP LeftHand P4000s that are in a management group Continue with the software upgrade instructions in the 1-Gigabit to 10-Gigabit Ethernet Migration Instructions. Upgrading HP LeftHand P4000s that are new and/or not in a management group 1. Open the CMC and find the P4000s
-
1 -
2 -
3
 |
 |
HP StorageWorks
P4000 10GbE SFP+ Hardware
Installation Instructions
© Copyright 2009, 2010 Hewlett-Packard Development Company,
L.P.
Second edition: June 2010
The information in this document is subject to change without notice.
Printed in the US
www.hp.com
*AX705-96003*
Overview
This document describes how to upgrade the HP LeftHand P4000 to
10 Gigabit Ethernet (GbE). Upgrade instructions vary depending on
whether the HP LeftHand P4000 is new and/or whether it is already in
a management group.
Prerequisite
The motherboard BIOS firmware must be up-to-date with the latest version
installed.
Table 1 General upgrade steps for P4000s
Download the software patch
Download software patch 10073. This procedure is the same regard-
less of the state or location of the P4000 storage node.
1.
Go to
h
t
tp://w
w
w
.hp
.co
m/su
ppo
r
t/s
t
o
r
age
.
2.
Select
P4000 SAN Solutions
.
3.
Select
Disk Storage Systems
>
P4000 SAN Solutions
>
HP
LeftHand P4000 SAN Solutions.
4.
Select
Download drivers and software
.
5.
Select your product.
6.
Select
Cross operating system (BIOS, Firmware, Diagnostics, etc.)
.
7.
Download the patch version 10073.
P4000 is in a management group
P4000 is new or not in a man-
agement group
Download the
HP StorageWorks
P4000 G1 Series 1GbE to 10GbE
SFP+ Migration Guide.
Follow instructions in the Migration
Guide for planning the upgrade.
Install hardware using the
HP
StorageWorks P4000 10GbE
SFP+ Hardware Installation In-
structions
Shut down the management group
using the instructions in the
Migra-
tion Guide.
Shutting down the
management group places it in
maintenance mode for the upgrade
process, and also powers off the
storage nodes, so that you can re-
move them from the rack.
Open the CMC and install
software patch 10073 onto the
P4000.
Install hardware using the
10GbE
SFP+ Hardware Installation Instruc-
tions.
Following instructions in the
1GbE
to 10GbE SFP+ Migration Guide
•
Open the CMC and install soft-
ware patch 10073 on the stor-
age node.
•
Configure network bonding on
the 10GbE ports if desired.
Installing the 10GbE board and RAM
Have the following items ready:
Page 1