HP Pavilion 14-e000 Regulatory, Safety and Environmental Notices User Guide - Page 39

Power supply and power cord set requirements, Power supply class I grounding requirements

Get HP Pavilion 14-e000 PDF manuals and user guides View all HP Pavilion 14-e000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

WARNING! Use of controls or adjustments or performance of procedures other than those specified herein or in the laser product's installation guide may result in hazardous radiation exposure. To reduce the risk of exposure to hazardous radiation: • Do not try to open the module enclosure. There are no user-serviceable components inside. • Do not operate controls, make adjustments, or perform procedures to the laser device other than those specified herein. • Allow only HP Authorized Service technicians to repair the unit. Power supply and power cord set requirements Power supply class I grounding requirements For protection from fault currents, the equipment shall be connected to a grounding terminal. Plug the system power cord into an AC outlet that provides a ground connection. Substitute cords may not provide adequate fault protection. Only use the power cord supplied with this product or a HewlettPackard authorized replacement. Brazil notice Este equipamento deve ser conectado obrigatoriamente em tomada de rede de energia elétrica que possua aterramento (três pinos), conforme a norma nbr abnt 5410,visando a segurança dos usuários contra choques elétricos. Denmark For tilslutning af de øvrige ledere, se medfølgende installationsvejledning. Finland Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan. Norway Apparatet må kun tilkoples jordet stikkontakt. Sweden Apparaten skall anslutas till jordat uttag, när den ansluts till ett nätverk. Power supply requirements The power supplies on some products have external power switches. The voltage select switch feature on the product permits it to operate from any line voltage between 100-127 or 200-240 volts AC. Power supplies on those products that do not have external power switches are equipped with internal circuits that sense the incoming voltage and automatically switch to the proper voltage. For safety reasons, use only the AC adapter provided with the unit or an authorized replacement adapter from Hewlett-Packard. Replacement part numbers may be found at http://www.hp.com/cgibin/hpsupport/index.pl. Power supply and power cord set requirements 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
WARNING!
Use of controls or adjustments or performance of procedures other than those specified
herein or in the laser product’s installation guide may result in hazardous radiation exposure. To
reduce the risk of exposure to hazardous radiation:
• Do not try to open the module enclosure. There are no user-serviceable components inside.
• Do not operate controls, make adjustments, or perform procedures to the laser device other than
those specified herein.
• Allow only HP Authorized Service technicians to repair the unit.
Power supply and power cord set requirements
Power supply class I grounding requirements
For protection from fault currents, the equipment shall be connected to a grounding terminal. Plug the
system power cord into an AC outlet that provides a ground connection. Substitute cords may not
provide adequate fault protection. Only use the power cord supplied with this product or a Hewlett-
Packard authorized replacement.
Brazil notice
Este equipamento deve ser conectado obrigatoriamente em tomada de rede de energia elétrica que
possua aterramento (três pinos), conforme a norma nbr abnt 5410,visando a segurança dos usuários
contra choques elétricos.
Denmark
For tilslutning af de øvrige ledere, se medfølgende installationsvejledning.
Finland
Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan.
Norway
Apparatet må kun tilkoples jordet stikkontakt.
Sweden
Apparaten skall anslutas till jordat uttag, när den ansluts till ett nätverk.
Power supply requirements
The power supplies on some products have external power switches. The voltage select switch
feature on the product permits it to operate from any line voltage between 100-127 or 200-240 volts
AC. Power supplies on those products that do not have external power switches are equipped with
internal circuits that sense the incoming voltage and automatically switch to the proper voltage.
For safety reasons, use only the AC adapter provided with the unit or an authorized replacement
adapter from Hewlett-Packard. Replacement part numbers may be found at
cgi-
bin/hpsupport/index.pl
.
Power supply and power cord set requirements
31