HP Pavilion Slimline s5-1200 Safety and Regulatory Information - Page 11

Japanese power cord requirements, Pinch hazard

Get HP Pavilion Slimline s5-1200 PDF manuals and user guides View all HP Pavilion Slimline s5-1200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Power cord sets for use in other countries must meet the requirements of the country where you use the product. For more information on power cord set requirements, contact your authorized HP dealer, reseller, or service provider. WARNING! Do not use power cords from other products. Mismatched power cords may result in a shock and fire hazard. The requirements listed below are applicable to all countries: 1. The power cord must be approved by an acceptable accredited agency responsible for evaluation in the country where the power cord set will be installed. 2. The length of the power cord must be between 1.8 m (6 feet) and 3.6 m (12 feet). For a power cord 2.0 m (6.56 feet) or less, the diameter of the wire must be a minimum of 0.75 mm2 or 18AWG. If the power cord is longer than 2.0 m (6.56 feet), the diameter of the wire must be a minimum of 1.0 mm2 or 16AWG. The power cord should be routed so that it is not likely to be walked on or pinched by items placed upon it or against it. Particular attention should be paid to the plug, electrical outlet, and the point where the cord exits from the product. WARNING! Do not operate this product with a damaged power cord set. If the power cord set is damaged in any manner, replace it immediately. Damaged cords may result in user exposure to hazards. Japanese power cord requirements For use in Japan, use only the power cord received with this product. CAUTION: Do not use the power cord received with this product on any other products. Pinch hazard WARNING! Observe pinch hazard areas. Keep fingers away from closing parts. Pinch hazard 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
Power cord sets for use in other countries must meet the requirements of the country where you use the
product. For more information on power cord set requirements, contact your authorized HP dealer,
reseller, or service provider.
WARNING!
Do not use power cords from other products.
Mismatched power cords may result in a shock and fire hazard.
The requirements listed below are applicable to all countries:
1.
The power cord must be approved by an acceptable accredited agency responsible for evaluation
in the country where the power cord set will be installed.
2.
The length of the power cord must be between 1.8 m (6 feet) and 3.6 m (12 feet). For a power
cord 2.0 m (6.56 feet) or less, the diameter of the wire must be a minimum of 0.75 mm
2
or
18AWG. If the power cord is longer than 2.0 m (6.56 feet), the diameter of the wire must be a
minimum of 1.0 mm
2
or 16AWG.
The power cord should be routed so that it is not likely to be walked on or pinched by items placed
upon it or against it. Particular attention should be paid to the plug, electrical outlet, and the point
where the cord exits from the product.
WARNING!
Do not operate this product with a damaged power cord set. If the power cord set is
damaged in any manner, replace it immediately. Damaged cords may result in user exposure to
hazards.
Japanese power cord requirements
For use in Japan, use only the power cord received with this product.
CAUTION:
Do not use the power cord received with this product on any other products.
Pinch hazard
WARNING!
Observe pinch hazard areas. Keep fingers away from closing parts.
Pinch hazard
5