HP Pavilion xt100 HP Pavilion ze5100 Series and HP Omnibook xe4400 Series Note - Page 143
Command, Function Conexant, ECC Commands, FAX Class 1
View all HP Pavilion xt100 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 143 highlights
Reference Information Modem Reference Information Command +MS=a,b,c,d,e,f +WS=n ECC Commands %Cn +EB=a,b,c +EFCS=0 +ER: a +ER=n +ES=a,b,c +ESR=0 +ETBM=a,b,c FAX Class 1 +FAE=n +FAR=n +FCL=n +FCLASS=n +FIT=n,a +FLO=a Function (Conexant) Select modulation (b, c, d, e, and f are optional). a is the carrier (allowable rates in parentheses): B103 (300), B212 (1200 Rx/75 Tx or 75 Rx/1200 Tx), V21 (300), V22 (1200), V22B (1200/2400), V23C (1200), V32 (4800/9600), V32B (4800-14400), V34 (2400-33600), K56 (32000-56000), V90 (28000-56000), V92 (downstream: 28000-56000; upstream: 24000-48000). b is automode: 0=disabled, 1=enabled (default). c is minimum transmit (Tx) rate (bps). d is maximum transmit rate (bps). e is minimum receive (Rx) rate. f is maximum receive rate (bps). Set PDC mode: 1=disable (default), 20=enable. Set data compression: 0=disable, 1=enable V.42 bis and MNP 5, 2=enable V.42 bis and MNP 5, 3=enable V.42 bis and MNP 5 (default). Select break handling (b and c are optional): a=0 - break is ignored. b=0 - transmitted V.42 L-SIGNAL will not indicate break signal length. c=0 - break is not delivered to DTE. Select 16-bit FCS specified in V.42. Select error control protocol: NONE=error control not in use, LAPM=V.42 LAPM protocol, ALT=MNP. Error control reporting: 0=disable, 1=enable. Select error control and synchronous mode (b and c are optional). a is requested mode when modem is originator: 0=initiate call with direct mode, 1=initiate call with normal mode, 2=initiate V.42 without detection phase, 3=initiate V.42 with detection phase (default), 4=initiate MNP, 6=initiate V.80 synchronous access mode when connection is completed. b specifies fallback mode when modem is originator: 0=LAPM, MNP, or normal mode error control optional (default); 1=LAPM, MNP, or direct mode error control optional; 2=LAPM or MNP error control required; 3=LAPM error control required; 4=MNP error control required. c specifies fallback mode when modem is answerer or specifies V.80 synchronous access mode: 1=error control disabled, use normal mode; 2=LAPM, MNP, or normal mode error control optional (default); 3=LAPM, MNP, or direct mode error control optional; 4=LAPM or MNP error control required; 5=LAPM error control required; 6=MNP error control required; 8=initiate V.80 synchronous access mode when connection complete. Disable selective repeat option in V.42. Handle data remaining in modem buffers on call termination (b and c are optional): a=0 - disconnect occurs immediately and buffered transmit data is discarded. b=0 - disconnect occurs immediately and buffered receive data is discarded. c=0 - modem does not attempt to deliver buffered data and discards data. Data/fax auto answer: 0=disable (default), 1=enable. 0=disable adaptive reception (default), 1=enable. Set loss-of-carrier delay in units of 100 ms (n=0 to 255). Set active service class: 0=data mode (default), 1=Fax Class 1, 1.0=Fax Class 1.0 mode, 8=voice mode. Set DTE inactivity timeout n seconds after which modem goes on-hook (a=0) or DCE goes on hook (a=1). Set flow control type: 0=XON/XOFF and RTS/CTS flow control turned off; 1=XON/XOFF flow control in either direction; 2=RTS for flow control of modem by DTE, and CTS for flow control of DTE by modem. Reference Guide 143