HP Pavilion xt178 HP Pavilion ze5100 Series and HP Omnibook xe4400 Series Note - Page 142
PTT testing of signal level: 00-09=DTMF dial 0-9, 0A=DTMF *, 0B=DTMF #, 0C=DTMF A, 0D=DTMF
View all HP Pavilion xt178 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 142 highlights
Reference Information Modem Reference Information Command +VRID=n -QCPC -QCPS=n &Cn &Dn &En &F0 &Gn &Kn &Mn &Pn &Q5 &Qn &T0 &T1 &V %TTn \N0 \N1 \N2 \N3 \N4 \N5 +MCR +MMR +MR=0 +MR=1 +MR=2 Function (Conexant) Report caller ID: 0=use formatted presentation, 1=use unformatted presentation. Use full startup procedures on next connection, then select startup procedure defined by +PQC. 0=do not allow modem to save generated quick-connect profile, 1=allow (default) Set RLSD: 0=always on, 1=follow carrier state (default). 0=ignore DTR; 1=upon on-to-off transition, enter online command state and issue OK result code; call remains connected; 2=upon on-to-off transition clear call, discard untransmitted data according to +ETBM. 0=disable line quality monitor, auto-retrain, and auto-rate renegotiation;1=enable line quality monitor, auto-retrain, and auto-rate renegotiation (default). Restore factory configuration. Included for compatibility only; no effect (returns OK). Set DTE/DCE flow control: 0=disable, 3=enable RTS/CTS DTE/DCE flow control (default), 4=enable XON/XOFF DTE/DCE flow control, 5 and 6 included for compatibility only (no effect, returns OK). Included for compatibility only; no effect (returns result code). Set pulse dial (pps) with make/break: 0=10 pps with 39%-61% make/break (default), 1=10 pps with 33%-67% make/break, 2=20 pps with 39%-61% make/break, 3=20 pps with 33%-67% make/break. Select asynchronous operation in error correction mode. (n=0-3, 6) Select asynchronous operation in normal mode (speed buffering). Terminate any test in progress. Initiate local analog loopback. Display current configuration and stored profiles. PTT testing of signal level: 00-09=DTMF dial 0-9, 0A=DTMF *, 0B=DTMF #, 0C=DTMF A, 0D=DTMF B, 0E=DTMF C, 0F=DTMF D, 10=V.21 Channel 1mark symbol, 11=V.21 Channel 2mark symbol, 12=V.23 Channel 1mark symbol, 13=V.23 Channel 2mark symbol, 14=Bell103 Channel 1mark symbol, 15=Bell103 Channel 2mark symbol, 20=V22Org, 21=V22Ans, 22=Bell212Org, 23=Bell212Ans, 24=V22BisOrg, 25=V22BisAns, 26=V32@4800, 27=V32@7200, 28=V32@9600, 29=V.32Bis@12000, 2A=V32Bis@14400, 30=Silence, 31=2100Hz MISC, 33=1300Hz MISC, 34=1100Hz MISC, 40=Reserved, 41=V27@2400 FAX, 42=V27@4800 FAX, 43=V29@7200 FAX, 44=V29@9600 FAX, 45=V17@7200LT FAX, 46=V17@7200ST FAX, 47=V17@9600LT FAX, 48=V17@9600ST FAX, 49=V17@12000LT FAX, 4A=V17@12000ST FAX, 4B=V17@14400LT FAX, 4C=V17@14400ST FAX. 5abc: a=bit rate (0=2400, D=33600), b=V.34 symbol rate (0=2400, 5=3429), c=pre-emphasis filter (0 to A). Select normal speed buffered mode. Select normal speed buffered mode. Select reliable (error-correction) mode. Select auto reliable mode. Force LAPM mode. Force MNP mode. Report carrier. Report transmit and receive rates. Disable reporting of modulation connection. Enable reporting of modulation connection (+MCR: and +MRR: are transmitted) (default). Enable reporting of modulation connection (+MCR: and Receive Rate Only: are transmitted). 142 Reference Guide