HP Pro 3130 Quick Setup & Getting Started Guide - Page 16

Helpful Hints, Maintenance and Service Guide - video

Get HP Pro 3130 - Minitower PC PDF manuals and user guides View all HP Pro 3130 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

● Remove any hardware that was recently added to your system. ● Remove any software that was recently installed. NOTE: For sales information and warranty upgrades (HP Care Pack), call your local authorized service provider or dealer. Helpful Hints If you encounter problems with the computer, monitor, or software, see the following list of general suggestions before taking further action: ● Check that the computer and monitor are plugged into a working electrical outlet. ● Check to see that the voltage select switch (some models) is set to the appropriate voltage for your region (115V or 230V). ● Check to see that the computer is turned on and the green power light is on. ● Check to see that the monitor is turned on and the green monitor light is on. ● Check the Power LED on the front of the computer to see if it is flashing. The flashing lights are error codes that will help you diagnose the problem. Refer to the Maintenance and Service Guide (English only) for details. ● Turn up the brightness and contrast controls of the monitor if the monitor is dim. ● Press and hold any key. If the system beeps, then the keyboard should be operating correctly. ● Check all cable connections for loose connections or incorrect connections. ● Wake the computer by pressing any key on the keyboard or pressing the power button. If the system remains in suspend mode, shut down the computer by pressing and holding the power button for at least four seconds. Then press the power button again to restart the computer. If the system will not shut down, unplug the power cord, wait a few seconds, then plug it in again. The computer will restart if automatic start on power loss is set in Computer Setup. If it does not restart, press the power button to start the computer. ● Reconfigure your computer after installing a non-plug and play expansion board or other option. ● Be sure that all the needed device drivers have been installed. For example, if you are using a printer, you need a driver for that model printer. ● Remove all bootable media (diskette, CD, or USB device) from the system before turning it on. ● If you have installed an operating system other than the factory-installed operating system, check to be sure that it is supported on the system. ● If the system has multiple video sources (embedded, PCI, or PCI-Express adapters) installed (embedded video on some models only) and a single monitor, the monitor must be plugged into the monitor connector on the source 8 Quick Setup & Getting Started ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
●
Remove any hardware that was recently added to your system.
●
Remove any software that was recently installed.
NOTE:
For sales information and warranty upgrades (HP Care Pack), call your
local authorized service provider or dealer.
Helpful Hints
If you encounter problems with the computer, monitor, or software, see the following
list of general suggestions before taking further action:
●
Check that the computer and monitor are plugged into a working electrical
outlet.
●
Check to see that the voltage select switch (some models) is set to the
appropriate voltage for your region (115V or 230V).
●
Check to see that the computer is turned on and the green power light is on.
●
Check to see that the monitor is turned on and the green monitor light is on.
●
Check the Power LED on the front of the computer to see if it is flashing. The
flashing lights are error codes that will help you diagnose the problem. Refer
to the
Maintenance and Service Guide
(English only) for details.
●
Turn up the brightness and contrast controls of the monitor if the monitor is
dim.
●
Press and hold any key. If the system beeps, then the keyboard should be
operating correctly.
●
Check all cable connections for loose connections or incorrect connections.
●
Wake the computer by pressing any key on the keyboard or pressing the power
button. If the system remains in suspend mode, shut down the computer by
pressing and holding the power button for at least four seconds. Then press
the power button again to restart the computer. If the system will not shut down,
unplug the power cord, wait a few seconds, then plug it in again. The computer
will restart if automatic start on power loss is set in Computer Setup. If it does
not restart, press the power button to start the computer.
●
Reconfigure your computer after installing a non–plug and play expansion
board or other option.
●
Be sure that all the needed device drivers have been installed. For example,
if you are using a printer, you need a driver for that model printer.
●
Remove all bootable media (diskette, CD, or USB device) from the system
before turning it on.
●
If you have installed an operating system other than the factory-installed
operating system, check to be sure that it is supported on the system.
●
If the system has multiple video sources (embedded, PCI, or PCI-Express
adapters) installed (embedded video on some models only) and a single
monitor, the monitor must be plugged into the monitor connector on the source
8
Quick Setup & Getting Started
ENWW