HP Pro UPS 500 240V HP R/T2200 UPS Installation Instructions - Page 2

Kit contents, Required tools, Selecting a site, Readying the equipment, Installing the UPS as a tower

Get HP Pro UPS 500 240V PDF manuals and user guides View all HP Pro UPS 500 240V manuals
Add to My Manuals
Save this manual to your list of manuals

Page 2 highlights

Kit contents This kit might contain extra hardware for your convenience. • Important Safety Information guide • This document and/or documentation CD • Warranty information • UPS • Front bezel, preinstalled • Rails, with mounting hardware for square- and round-holed racks • Bezel assembly (Retma rail covers and logo badge) • Tower stand kit • Communications port/option slot, preinstalled • REPO port connector block • Serial computer interface cable • USB computer interface cable • RJ-11 phone cable • Jumper cords for load equipment power (INTL model only) If you have the HP Enterprise Infrastructure Solutions Management Pack CD, use the CD to install HP Power Manager software. To download the latest version of HP Power Manager software and UPS firmware, see the HP website (http://www.hp.com/products/ups). Required tools • No. 2 Phillips screwdriver • T-20 Torx screwdriver Selecting a site WARNING: To prevent fire or electric shock, install the unit in a temperature- and humidity-controlled indoor environment, free of conductive contaminants. When selecting a site, consider the following factors: • Elevated operating ambient temperature-If the equipment is installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment might be greater than room ambient temperature. Install the equipment in an environment compatible with the operating temperature. • Reduced air flow-In the rack, the rate of air flow required for safe operation of the equipment must not be compromised. • Circuit overloading-Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern. • Reliable earthing-Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given to supply connections other than direct connections to the branch circuit, such as the use of power strips. • Electrical requirements-All models require a dedicated (unshared) branch circuit, suitably rated for the specific UPS as stated in "Input specifications" in the user guide. Readying the equipment 1. Check the battery recharge date specified on the label that is affixed to the shipping carton. IMPORTANT: Do not use the battery if the recharge date has passed. If the date on the battery recharge date label has passed without the battery being recharged, contact an HP authorized service representative for directions. 2. Transport the packaged unit to its installation location. 3. Unpack the equipment near the rack where the unit will be assembled. CAUTION: Always plan the rack installation so that the heaviest item is on the bottom of the rack. Install the heaviest item first, and continue to populate the rack from the bottom to the top. Installing the UPS as a tower Before installing the unit, review and adhere to all warnings provided in "Precautions." 1. Remove the UPS front bezel. 2. Attach the logo badge above the LED/Control panel.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
Kit contents
This kit might contain extra hardware for your convenience.
•
Important Safety Information
guide
•
This document and/or documentation CD
•
Warranty information
•
UPS
•
Front bezel, preinstalled
•
Rails, with mounting hardware for square- and round-holed
racks
•
Bezel assembly (Retma rail covers and logo badge)
•
Tower stand kit
•
Communications port/option slot, preinstalled
•
REPO port connector block
•
Serial computer interface cable
•
USB computer interface cable
•
RJ-11 phone cable
•
Jumper cords for load equipment power (INTL model only)
If you have the HP Enterprise Infrastructure Solutions Management
Pack CD, use the CD to install HP Power Manager software. To
download the latest version of HP Power Manager software and UPS
firmware, see the HP website (http://www.hp.com/products/ups
).
Required tools
•
No. 2 Phillips screwdriver
•
T-20 Torx screwdriver
Selecting a site
WARNING:
To prevent fire or electric shock, install the
unit in a temperature- and humidity-controlled indoor
environment, free of conductive contaminants.
When selecting a site, consider the following factors:
•
Elevated operating ambient temperature—If the equipment is
installed in a closed or multi-unit rack assembly, the operating
ambient temperature of the rack environment might be greater
than room ambient temperature. Install the equipment in an
environment compatible with the operating temperature.
•
Reduced air flow—In the rack, the rate of air flow required for
safe operation of the equipment must not be compromised.
•
Circuit overloading—Consideration should be given to the
connection of the equipment to the supply circuit and the effect
that overloading of the circuits might have on overcurrent
protection and supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing
this concern.
•
Reliable earthing—Reliable earthing of rack-mounted
equipment should be maintained. Particular attention should be
given to supply connections other than direct connections to the
branch circuit, such as the use of power strips.
•
Electrical requirements—All models require a dedicated
(unshared) branch circuit, suitably rated for the specific UPS as
stated in "Input specifications" in the user guide.
Readying the equipment
1.
Check the battery recharge date specified on the label that is
affixed to the shipping carton.
IMPORTANT:
Do not use the battery if the recharge date
has passed. If the date on the battery recharge date label
has passed without the battery being recharged, contact
an HP authorized service representative for directions.
2.
Transport the packaged unit to its installation location.
3.
Unpack the equipment near the rack where the unit will be
assembled.
CAUTION:
Always plan the rack installation so that the
heaviest item is on the bottom of the rack. Install the
heaviest item first, and continue to populate the rack from
the bottom to the top.
Installing the UPS as a tower
Before installing the unit, review and adhere to all warnings
provided in "Precautions."
1.
Remove the UPS front bezel.
2.
Attach the logo badge above the LED/Control panel.