HP ProLiant BL45p HP ProLiant Servers Troubleshooting Guide - Page 123
ssors were detected. System cannot proceed., WARNING, ING - iLO 2 not responding. System health
View all HP ProLiant BL45p manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 123 highlights
Select a configuration option: 1. Enable OBDR 2. Exit Audible Beeps: None Possible Cause: A USB tape device that supports One Button Disaster Recovery (OBDR) is installed in the system. Action: 1. Press 1 or 2. o Pressing 2 exits the configuration. o Pressing 1 starts the configuration. The following message appears Attempting to enable OBDR for the attached USB tape drive... 2. Observe the configuration progress. The following error may appear: Error - USB tape drive not in Disaster Recovery mode. 3. Follow the onscreen directions: Remove power to USB drive and reboot. The following message should appear: OBDR is now enabled for the attached USB tape drive. WARNING: A Type 2 Header PCI Device Has Been Detected... The BIOS will not configure this card. It must be configured properly by the OS or driver. Audible Beeps: 2 short Possible Cause: Only Type 0 and Type 1 Header PCI Devices are configured by the system ROM. The device will not work unless the OS or device driver properly configure the card. Typically this message only occurs when PCI cards with a PCI to PCMCIA bridge are installed. Action: Refer to the operating system documentation or the device driver information that ships with the Type 2 PCI device. WARNING - iLO 2 not responding. System health monitoring has been disabled. Audible Beeps: None Possible Cause: The iLO and iLO 2 firmware is not responding. The iLO and iLO 2 Firmware may be corrupt. Action: If the iLO and iLO 2 firmware is corrupt, update the iLO and iLO 2 firmware using the Firmware Maintenance CD. WARNING - Mixed Stepping Processors were detected. System cannot proceed. Audible beeps: 1 long, 1 short Possible cause: One or more 800-MHz front side bus speed processors have been initialized at 667MHz. Action: Correct the processor configuration. Error messages 123
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188