HP ProLiant SL335s HP ProLiant SL335s G7 Server Installation Sheet - Page 1

HP ProLiant SL335s G7 Server Installation Sheet Identifying Server Components Front Panel Components SL335s G7 Server Front Panel Components Figure 1 Front panel components of the s6500 chassis with 8 SL335s G7 server First edition (February 2010) Part number 633289-001 Important Safety Information Læs dokumentet Vigtige sikkerhedsoplysninger på dokumentations-cd'en, før produktet installeres. Prima dell'installazione, leggere sul CD le Informazioni importanti sulla sicurezza. Item Description 1 Serial port 2 VGA port 3 Top: USB 2.0 Port Bottom: USB 2.0 Port 4 IPMI Connector NIC1 Connector NIC2 Connector 5a Server handle 5b Server latch 6 Power LED/SW 7 Health LED 8 UID LED/SW 9 Server 1 10 Server 2 11 Server 3 12 Server 4 13 Server 5 14 Server 6 15 Server 7 16 Server 8 Rear Panel Components Figure 2 Rear panel components of the s6500 chassis with 8 SL335s G7 server Les "Viktig sikkerhetsinformasjon" på dokumentasjons-CDen før du installerer dette produktet. Tärkeisiin turvatietoihin" Documentation CD -levyllä ennen tuotteen asentamista. Läs dokumentet Viktig säkerhetsinformation på dokumentations-cd:n innan du installerar denna produkt. Legal notices © Copyright 2010 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. Microsoft, Windows, and Windows NT are U.S. registered trademarks of Microsoft Corporation. Windows Server 2003 is a trademark of Microsoft Corporation. Intel, Pentium, and Itanium are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. Item Description 1 Power Supply 1 Item Description 2 Power Supply 2 3 Power Supply 3 4 Power Supply 4 5 UID LED/SW 6 SLAPM connector 7 Fan 1 8 Fan 2 9 Fan 3 10 Fan 4 11 Fan 5 12 Fan 6 13 Fan 7 14 Fan 8 Server Configuration Resources In addition to this Installation Sheet, other resources are available for more information regarding the configuration and maintenance of your server: • For safety information and detailed procedures relating to installation of options, refer to any installation instructions that came with the option, as well as the HP ProLiant SL335s G7 Server Maintenance and Service Guide. • For safety information, regulatory notices, and detailed procedures related to the rest of the steps listed in the "Configuring the Server" section, refer to relevant chapter of the HP ProLiant SL335s Server User Guide. • Refer to the HP ProLiant SL335s G7 Server Documentation CD for additional information and updates not provided in this installation sheet. You can also access additional information and documentation from the HP website at http://www.hp.com/, either by connecting directly or through the Documentation CD. Server Configuration Overview The steps listed below give an overview of the necessary setup procedures for preparing the HP ProLiant SL335s G7 Server for operation: 1. Connect the AC power cord and peripheral devices. 2. Power up the server. 3. Press "F10" to enter BIOS setup. 4. Note the server BIOS version. 5. Verify the server BIOS version against the latest BIOS version listed for this server on the HP website: http://www.hp.com. 6. If you do not have the latest BIOS, update the BIOS now. Refer to the HP ProLiant SL335s G7 Server Maintenance and Service Guide available on the HP website: http://www.hp.com. 7. Install a supported operating system of your choice. For detailed procedures, refer to the documentation provided by the operating system vendor. For a list of operating systems supported by your ProLiant server, go to http://www.hp.com/go/supportos. Pre- and Post-installation Procedures When installing additional options in your HP ProLiant SL335s G7 Server, observe the following procedures: Pre-installation procedures 1. Turn off the server and all the peripherals connected to it. 2. Remove the server from the chassis by following the procedure described later in the "Removing the server" section. Post-installation procedures 1. Be sure all components are installed according to the described step-by-step instructions. 2. Check to make sure you have not left loose tools or parts inside the server. 3. Reinstall the PCI riser, peripherals, and system cables that you have removed. 4. Reinstall the server into the chassis. 5. Connect all external cables to the system. 6. Press the power button on the front panel to turn on the server. Removing the Server You need to remove the server from the chassis before you can remove or replace a server component. To remove server: 1. Press the latch to release the handle. 2. Rotate the handle to disengage the power connector. 3. Extend the server from the chassis until the release latch catches. 4. Firmly holding the server, press the release button. 5. Remove the server from chassis. 6. Install the server blank in the server slot. Figure 3 Removing the SL335s G7 left server Figure 4 Removing the SL335s G7 right server Installing the Hard Disk Drive One SL335s G7 server tray can accommodate up to 4 LFF hard disk drives, and the chassis can accommodate 8 server trays for up to 32 LFF hard disk drives. The server supports both SAS and SATA hard disk drives. CAUTION: Drives can be damaged by static electricity. Before handling drives, touch an unpainted metal surface to discharge static electricity. To install the hard disk drive in the server tray: 1. Unlock the HDD carrier latches. 2. Rotate the HDD carrier handle up. 3. Insert the HDD carrier and align the pins. 4. Rotate the HDD carrier handle down. 5. Lock the HDD carrier latches.