HP Spectre 14-3100 HP ENVY14 SPECTRE Maintenance and Service Guide IMPORTANT! - Page 42

Solid-state drive, Remove the Phillips PM2.0×2.0 screw

Get HP Spectre 14-3100 PDF manuals and user guides View all HP Spectre 14-3100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Solid-state drive Description 256-GB SATA III solid-state drive 128-GB SATA III solid-state drive 128-GB SATA II solid-state drive Spare part number 698645-001 697235-001 675508-001 Before removing the solid-state drive and cable, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the battery (see Battery on page 32). Remove the solid-state drive: 1. Remove the Phillips PM2.0×2.0 screw (2) that secures the solid-state drive to the system board. (The solid-state drive tilts up.) 2. Remove the solid-state drive by pulling the drive away from the slot at an angle (2). NOTE: The solid-state drive is designed with a notch to prevent incorrect installation into the solid-state drive slot. 34 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
Solid-state drive
Description
Spare part number
256-GB SATA III solid-state drive
698645-001
128-GB SATA III solid-state drive
697235-001
128-GB SATA II solid-state drive
675508-001
Before removing the solid-state drive and cable, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the battery (see
Battery
on page
32
).
Remove the solid-state drive:
1.
Remove the Phillips PM2.0×2.0 screw
(2)
that secures the solid-state drive to the system board.
(The solid-state drive tilts up.)
2.
Remove the solid-state drive by pulling the drive away from the slot at an angle
(2)
.
NOTE:
The solid-state drive is designed with a notch to prevent incorrect installation into
the solid-state drive slot.
34
Chapter 4
Removal and replacement procedures