HP StorageWorks 1200mx HP SureStore 1200mx/2200mx Optical Jukebox User&#03 - Page 25

Connecting a 10-Drive Jukebox as the Only Peripheral, Two Host, Adapters, Basic SCSI

Get HP StorageWorks 1200mx PDF manuals and user guides View all HP StorageWorks 1200mx manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Chapter 1: Setting upStheettiDngiskUpDrthivee Jukebox Figure 1-3 Setting Up the Jukebox Connecting a 10-Drive Jukebox as the Only Peripheral, Two Host Adapters, Basic SCSI Addressing 4. Remove the customer access panel by pulling on the bottom of the panel and then lifting it off (see Figure 1-1). (If screws are installed, use a flatblade screwdriver or T-15 Torx driver.) Connecting a 10-Drive Jukebox, Two Host Adapters, Basic SCSI Addressing 5. Plug a SCSI terminator into the unused SCSI connector of interface type you chose (the example diagram shows terminators for the two differential interfaces placed on the "B1" port for each interface ). If you are using the differential interface, use a 68-pin high-density terminator. If you are using the single-ended interface, use a 50-pin high-density terminator. 6. Plug a SCSI terminator into one of SCSI ports on each unused interface (the example diagram shows the terminators on the single-ended port at "A2" for both interfaces). The terminators can be placed on either port of the unused interface. Use a 50-pin high-density terminator for the single-ended interface or a 68-pin terminator for the differential interface. 7. To continue with the installation, go to "Connecting Power" in this Chapter. Chapter 1 1-13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
Chapter 1
1-13
Setting Up the Jukebox
Connecting a 10-Drive Jukebox as the Only Peripheral, Two Host
Adapters, Basic SCSI Addressing
Chapter 1: Setting
up the Disk Drive
Setting Up the
Jukebox
4.
Remove the customer access panel by pulling on the bottom of the panel and
then lifting it off (see Figure 1-1). (If screws are installed, use a flatblade
screwdriver or T-15 Torx driver.)
Figure 1-3
Connecting a 10-Drive Jukebox, Two Host Adapters, Basic SCSI Addressing
5.
Plug a SCSI terminator into the unused SCSI connector of interface type you
chose (the example diagram shows terminators for the two differential interfaces
placed on the
“
B1
”
port for each interface ).
If you are using the differential interface, use a 68-pin high-density terminator. If
you are using the single-ended interface, use a 50-pin high-density terminator.
6.
Plug a SCSI terminator into one of
SCSI ports on each unused interface (the
example diagram shows the terminators on the single-ended port at
“
A2
”
for
both interfaces). The terminators can be placed on either port of the unused
interface.
Use a 50-pin high-density terminator for the single-ended interface or a 68-pin
terminator for the differential interface.
7.
To continue with the installation, go to
“
Connecting Power
”
in this Chapter.