Home » HP Manuals » Storage Devices » HP StorageWorks 2/16 » Manual Viewer

HP StorageWorks 2/16 SAN switch 2/16 version 3.0.x installation guide - Page 54

Modifying Domain IDs, Core Switch PID Format: 0..1 [0], SwitchEnable, cfgEnable, Fabric parameters

View all HP StorageWorks 2/16 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

Installing the SAN Switch 2/16 5. Locate the line, "Core Switch PID Format: (0..1) [0] 1," and select 1. 6. Press Enter until the following prompt appears. Committing configuration...Done 7. At the prompt type, SwitchEnable. 8. After setting the Core PID to match the the other switches in the fabric, see "Connecting the Switch to the Fabric" on page 55 in this chapter for instructions on connecting Fibre Channel cables. 9. If necessary, type cfgEnable to re-establish zoning. Note: Once the switch PID format is set, it is stored in the flash memory of the switch and it is NOT necessary to set it again during subsequent firmware upgrades. Modifying Domain IDs Optional. Modify the domain IDs, if desired, as follows. Note: The default domain ID is 1. If the default domain ID is already in use when the switch is connected to the fabric, the domain ID for the new switch is automatically reset to a unique value. The domain IDs that are currently in use can be determined using the telnet command fabricShow. 1. Disable the switch by entering the following: switchDisable 2. Enter the following: configure 3. Enter y after the Fabric parameters prompt. Fabric parameters (y, n) 4. Enter a unique domain ID (such as the domain ID used by the previous switch, if still available). Domain: (1..239) [1] 3 5. Complete the remaining prompts (or press CTRL+D to accept the remaining settings without completing all the prompts). 54 hp StorageWorks SAN Switch 2/16 Installation Guide

Section	Page
Contents	3
About this Guide	9
Overview	10
Intended Audience	10
Related Documentation	10
Conventions	11
Document Conventions	11
Table 1: Document Conventions	11
Text Symbols	11
Equipment Symbols	12
Rack Stability	14
Getting Help	15
HP Technical Support	15
HP Storage Website	15
HP Authorized Reseller	16
Overview	17
SAN Switch 2/16 Features	18
Firmware	18
Hardware	19
SFP Media Side	20
Figure 1: SFP media side	20
Optical Ports	20
ISL Trunking	21
SFPs	21
Power Supply Side	21
Figure 2: Power supply side	21
Field-Replaceable Units	21
Optional Hardware Kits	22
Table 2: SAN Switch 2/16 Orderable Hardware	22
Installing the SAN Switch 2/16	23
Unpack and Verify Carton Contents	24
Figure 3: Carton contents	25
Table 3: Shipping Carton Contents	26
Installation and Safety Considerations	27
Selecting an Operating Location	27
Cooling Requirements	27
Power Requirements	28
Electrostatic Discharge Precautions	28
Installing the SAN Switch as a Stand-alone Unit	29
Installing the SAN Switch 2/16 in an HP 9000 Series or Comparable EIA Rack	30
Installing the Slide Rail Assemblies to the Switch	30
Separating the Inner Slide Rail Assembly from the Outer Slide Rail Assembly	30
Attaching the Inner Slide Rails to the Switch	31
Figure 4: Securing the inner slide rails to the switch	32
Attaching the Rear or Front Rack Mount Brackets	32
For Rear Rack Access	33
Figure 5: Attaching the rear rack mount brackets	33
For Front Rack Access	34
Attaching the Outer Slide Rails	34
Figure 6: Attaching the outer slide rails to the HP 9000 Series rack	36
Sliding the Switch into an HP 9000 Series or EIA Rack	37
Figure 7: Sliding the switch into an HP 9000 Series rack	38
Securing the Rack Mount Brackets	38
Installing the Switch in the Optional HP System/e Rack	39
Items Required for the HP System/e Rack	39
Figure 8: Installing the mounting brackets	40
Figure 9: Installing the tinnerman clips	41
Figure 10: Installing the rubber washers	42
Figure 11: Assembling the outer rails (HP rack)	43
Figure 12: Assembling the inner rails	43
Figure 13: Installing switch into the HP rack	44
Connecting AC Power	45
Figure 14: Connecting the power cords	45
Power-On Self Test	46
Checking POST Results	47
Configuring Network Addressing	47
Requirements	47
Setting Network Addresses via a Serial Connection	48
Figure 15: Connecting the Serial cable	48
Connecting the Switch to the LAN	51
Figure 16: Connecting the Ethernet cable	51
Important Information on Setting the CORE PID Format	52
How to Check the Current Core PID Setting	52
How to Change the Core PID Format	53
Modifying Domain IDs	54
Specifying Custom Status Policies	55
Connecting the Switch to the Fabric	55
Figure 17: Inserting a cable into an SFP	56
Verifying Operation	56
Installing Multiple Switches into an Existing SAN	57
Next Steps	58
Setting QuickLoop Mode on Ports	58
Setting Up Speed Negotiation	58
Cascading Switches	59
Managing the SAN Switch 2/16	61
Interpreting LED Activity	62
Front Panel LEDs	62
Table 4: Front Panel LED Patterns During Normal Operation	63
Rear Panel LEDs	66
Table 5: Rear Panel LED Patterns During Normal Operation	66
Management Overview	68
Optional Management Features	68
Displaying the Optional Feature Licenses	68
Enabling Licensed Features	68
Running Basic Switch Operations Using Telnet	69
Logging into the Switch	69
Changing the Admin Password and User ID	70
Configuring the IP and Fibre Channel Address	70
Displaying Devices within the Fabric	71
Checking the Firmware Version	71
Setting the Switch Date and Time	71
Displaying Switch Configuration Settings	72
Diagnostic Tests	73
Interpreting POST Results	73
Diagnostic Tests	73
Backing Up the Configuration and Upgrading Firmware	75
Backing Up System Configuration Settings	76
Restoring the System Configuration Settings	77
Upgrading or Restoring the Switch Firmware	78
Downloading Firmware from the HP Website	79
Regulatory Compliance Notices	81
FCC EMC Statement (USA)	81
EMC Statement (Canada)	82
EMC Statement (European Union)	82
Spécification ATI Classe A (France)	82
Germany Noise Declaration	82
VCCI EMC Statement (Japan)	82
Harmonics Conformance (Japan)	83
BSMI EMC Statement (Taiwan)	83
RRL EMC Statement (Korea)	83
Laser Safety	84
Battery Replacement Notice	85
Electrostatic Discharge	87
Grounding Methods	88
Technical Specifications	89
Dimensions	90
Table 6: Physical Specifications	90
Power Supply Specifications	91
Table 7: Power Supply Specifications	91
Environmental Requirements	92
Table 8: Environmental Requirements	92
Memory Specifications	93
Table 9: Cabling Pinouts if Pin 7 is Used	93
Glossary	95
Index	107
A	107
B	107
C	107
D	107
E	108
F	108
G	108
H	108
I	108
L	108
M	108
N	108
O	108
P	108
R	109
S	109
T	109
U	109
V	109
W	110