HP StorageWorks 4/64 Brocade Converged Enhanced Ethernet Command Reference v6.
HP StorageWorks 4/64 - SAN Switch Manual
View all HP StorageWorks 4/64 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP StorageWorks 4/64 manual content summary:
- HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 1
53-1001347-01 28 July 2009 Converged Enhanced Ethernet Command Reference Supporting Fabric OS v6.3.0 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 2
any equipment, equipment feature, or service offered or to be offered by Brocade. Brocade reserves the right to make brocade.com/support/oscd. Brocade Communications Systems, Incorporated Corporate and Latin American Headquarters Brocade Communications Systems, Inc. 1745 Technology Drive San - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 3
In this chapter ix How this document is organized ix Supported hardware and software x What's new in this document xi Document feedback xv Chapter 1 CLI Basics In this chapter 1 Accessing the Brocade CEE Switch 1 CLI command modes 1 L2 ACL commands 3 Chapter 2 Configuration Management - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 4
show media 28 show media interface 29 show media linecard 30 show processes cpu 31 show processes memory 32 show running-config 33 show startup-config 34 show system 35 show tech-support 36 show users 37 show version 38 terminal length 39 terminal monitor 40 write erase 41 write memory - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 5
57 description 58 interface 59 mtu 60 show interface 61 show ip interface 63 shutdown 65 Link Layer Discovery Protocol Commands advertise dcbx 76 hello 77 lldp dcbx-version 78 lldp disable 79 lldp fcoe-priority-bits 80 lldp profile 81 mode 82 multiplier 83 profile 84 protocol lldp 85 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 6
Chapter 6 Chapter 7 Chapter 8 Chapter 9 show lldp neighbors 88 show lldp statistics 90 system-description LINE 91 system-name 92 Link Aggregation Control Protocol Commands channel-group 93 clear lacp 95 clear lacp counters 96 debug lacp 97 lacp system-priority 99 lacp timeout 100 show - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 7
clear spanning-tree counter 127 debug spanning-tree 128 error-disable-timeout enable 129 error-disable-timeout interval 130 forward-delay 131 hello-time 132 instance 133 max-age 134 max-hops 135 port-channel path-cost 136 protocol spanning-tree 137 region 138 revision 139 show spanning- - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 8
Chapter 10 Chapter 11 Chapter 12 RMON Commands rmon alarm 165 rmon collection stats 167 rmon event 168 show rmon 169 QoS Commands cee 171 cee-map 172 priority-group-table 173 priority-table 174 qos cos 176 qos cos-mutation 177 qos cos-traffic-class 178 qos map cos-mutation 179 qos map - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 9
dot1x reauthentication 204 dot1x reauthMax 205 dot1x timeout re-authperiod 206 dot1x timeout server-timeout 207 dot1x timeout supp-timeout 208 dot1x timeout tx-period 209 show dot1x 210 show dot1x all 211 show dot1x diagnostics interface 213 show dot1x interface 214 show dot1x session-info - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 10
viii Converged Enhanced Ethernet Command Reference 53-1001347-01 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 11
components: • Chapter 1, "CLI Basics" describes how to access the switch and the CEE CLI command modes. • Chapter 2, "Configuration Management Commands 5, "Link Layer Discovery Protocol Commands" describes the commands that support the Link Layer Discovery Protocol (LLDP) implementation. • Chapter - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 12
5000 • Brocade 5100 • Brocade 5300 • Brocade 5410 • Brocade 5424 • Brocade 5450 • Brocade 5480 • Brocade 7500 • Brocade 7500E • Brocade 7600 • Brocade 7800 • Brocade 8000 • Brocade Encryption Switch • Brocade DCX • Brocade DCX-4S • Brocade 48000 • Brocade FCOE10-24 port blade Within this manual, any - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 13
For readability, command names in the narrative portions of this guide are presented in mixed lettercase: for example, MTU. In is case sensitive. . Command syntax conventions Command syntax in this manual follows these conventions: TABLE 1 Command syntax conventions Convention Description bold - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 14
of these conditions or situations. Key terms For definitions specific to Brocade and Fibre Channel, see the technical glossaries on Brocade Connect. See "Brocade resources" on page xiii for instructions on accessing Brocade Connect. Notice to the reader This document may contain references to - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 15
site and are also bundled with the Fabric OS firmware. Other industry resources • White papers, online demos, and data sheets are available through the Brocade Web site at http://www.brocade.com/products/software.jhtml. • Best practice guides, white papers, data sheets, and other documentation is - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 16
and messages received • supportSave command output • Detailed description of the problem, including the switch or fabric behavior immediately following the problem, and specific questions • Description of any troubleshooting steps already performed and the results • Serial console and Telnet session - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 17
an error or an omission, or you think that a topic needs further development, we want to hear from you. Forward your feedback to: [email protected] Provide the title and version number of the document and as much detail as possible about your comment, including the topic heading and page - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 18
xvi Converged Enhanced Ethernet Command Reference 53-1001347-01 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 19
an example of logging in to a switch supporting FCoE and CEE. telnet 10.32.152.21 switch login: admin Password:xxxxxx switch cmsh - cmsh takes you to the CEE Brocade8000 CLI prompt. switch> CLI command modes Following are the main command modes for the Brocade FCoE hardware: • EXEC • Privileged EXEC - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 20
display and change system parameters. From the EXEC mode, enter the Configure features that affect the configure terminal EXEC command. entire switch. From the global configuration mode, specify an interface by entering one of the following interface types: • interface port-channel • interface - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 21
access control lists to test source and destination addresses and other IP packet data, such as protocols, TCP or UDP port numbers, type of service and to provide Reflective access-lists and Time-based access-lists.capabilities. Converged Enhanced Ethernet Command Reference 3 53-1001347-01 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 22
1 L2 ACL commands 4 Converged Enhanced Ethernet Command Reference 53-1001347-01 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 23
. startup--config Copies to the current running configuration file. Defaults There are no usage guidelines for this command. Command Privileged Examples To copy the source file to a remote machine using FTP: switch#copy ftp://[email protected]/file1 file2 Source password[]? To copy the source - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 24
-config Copies to the current running configuration. Defaults There are no default configurations for this command. Command Privileged EXEC • An error displays if there is no startup configuration file, for example: switch #copy startup-config file2 % Error: No Startup-config. • Use the write - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 25
Operands filename Specifies the name of the file to be deleted from the Flash of the local switch using the following format: [flash://]filename. Defaults There is no default configuration for this command. Command Privileged EXEC mode Modes Description Use this command to delete a file from - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 26
The default is the current directory. Command Privileged EXEC mode Modes Description Use this command to list the contents of the current directory. Usage There are no usage guidelines for this command. Guidelines Examples To list the contents of the current directory: switch#dir Contents - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 27
returns to the EXEC mode. Synopsis disable Operands none Defaults There are no default configurations for this command. Command Privileged EXEC mode Modes Description to the EXEC mode: switch#disable switch> See Also enable, end, exit Converged Enhanced Ethernet Command Reference 9 53- - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 28
Operands command Specifies the command you want to run. Defaults There are no default configurations for this command. Command All configuration modes Modes rw-r----switch(config)# 1276 1276 1276 1276 Wed Feb 4 07:08:49 2009 Wed Feb 4 07:10:30 2009 Wed Feb 4 07:12:33 2009 Wed Feb 4 10:48: - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 29
the Privilege EXEC mode. Synopsis enable Operands none Defaults There are no default configurations for this command. Command EXEC mode Modes Description To enable the Privileged EXEC mode: switch> enable switch# See Also disable Converged Enhanced Ethernet Command Reference 11 53-1001347- - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 30
from all configuration modes. Synopsis end Operands none Defaults There are no default configurations for this command. Command All configuration modes from interface configuration mode: switch(config)#interface tengigabitethernet 0/0 switch(conf-if-te-0/0)#end switch# See Also exit, disable - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 31
There are no default configurations for this command. Command Configuration mode Modes Description Use this command to erase the files from the Flash. Usage There are no usage guidelines for this command. Guidelines Examples To erase the files from the Flash: switch#erase flash %% Warning - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 32
the time interval in seconds. The range is 0-2147483. Defaults The default is 10 minutes. Command Console and VTY (line) configuration mode for the console session: switch(config)#line console 0 switch(conf-line)#exec-timeout 2 30 switch(config)#line vty 0 9 switch(conf-line)#exec-timeout - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 33
and returns to the previous mode. Synopsis exit Operands none Defaults There are no default configurations for this command. Command All command modes Modes to the Configuration mode: switch(config)#interface tengigabitethernet 0/0 switch(conf-if-te-0/0)#exit switch(config)#exit See Also - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 34
Synopsis fos command Operands command Specifies the Fabric OS command. Defaults There are no default configurations for this command. Command Privileged EXEC mode Modes Description portstatsclear portstatsshow slotpoweroff slotpoweron slotshow 16 Converged Enhanced Ethernet Command Reference - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 35
commands. The fcoelogincfg, fcoelogingroup, and fcoelogincfg commands are not supported from cmsh shell. See the Fabric OS Command Reference for command switchshow from the Privilege EXEC mode: switch#fos switchshow switchName: switch switchType: 76.6 switchState: Online switchMode: Native - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 36
mode. Synopsis line console 0 Operands none Defaults There are no default configurations for this command. Command Global configuration mode the console session: switch>enable switch#configure terminal switch(config)#line console 0 switch(config-line)#exec-timeout 2 30 switch(config-line)#exit - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 37
line number. The range of valid values is 0-31. Defaults There are no default configurations for this command. Command Global configuration mode Modes if there is no response from the user: switch#configure terminal switch(config)#line vty 23 31 switch(conf-line)#exec-timeout 2 30 See Also show - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 38
There are no default configurations for this command. Command Privileged EXEC mode Modes Description Use this command to view the current working directory. Usage There are no usage guidelines for this command. Guidelines Examples To view the current working directory: switch#pwd flash: See - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 39
change. Specifies the new name of the file. Defaults There are no default configurations for this command. Command Privileged EXEC mode Modes rename a file in the Flash: switch#rename file1 file2 switch#dir Contents of flash:// -rw-r----- 1276 Wed Feb 4 13:16:00 2009 file2 See Also none - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 40
time based on the switch hardware clock. Synopsis show calendar Operands none Defaults There are no default configurations for based on the switch hardware clock. Usage There are no usage guidelines for this command. Guidelines Examples To display calendar information: switch#show calendar 16 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 41
no default configurations for this command. Command Privileged EXEC mode Modes Description Use this command to display the time and date from the system clock. Usage There are no usage guidelines for this command. Guidelines Examples To display the time and date from the system clock: switch - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 42
2 show environment show environment Displays fan, temperature, redundant power system (RPS) availability, and power information for the switch. Synopsis show environment Operands none Defaults There are no default configurations for this command. Command Privileged EXEC mode Modes Description - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 43
default configurations for this command. Command Privileged EXEC mode Modes Description Use this command to display the contents of a text file in the local Flash. Usage There are no usage guidelines for this command. Guidelines Examples To show the file system for internal flash: switch#show - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 44
. The range of valid values is 0-31. Defaults If the line is not specified, it displays vty 13 Idle vty 14 Idle vty 15 Idle vty 16 Idle vty 17 Idle vty 18 Idle vty 19 24 24 24 24 24 24 24 24 24 24 24 24 24 switch#show line 0 Status Type Idle console 0 * Active vty 0 Timeout(m/s) - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 45
show logging 2 show logging Displays the internal syslog buffer of the switch. Synopsis show logging Operands none Defaults There are no default configurations for this command. Command Privileged EXEC mode Modes Description Use this command to display the RASlog messages stored in the - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 46
on a switch. Synopsis show media Operands none Defaults There are no default configurations for (units 10 meters) Length Cu 0 (units 1 meter) Vendor Name BROCADE Vendor OUI 42:52:4f Vendor PN 57-0000075-01 Vendor Rev 0.002 (mAmps) TX Power 0.1 (uWatts) RX Power 0.1 (uWatts) (output - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 47
valid port number. Defaults There are no default configurations for this interface: switch#show media 10 meters) Length Cu 0 (units 1 meter) Vendor Name BROCADE Vendor OUI 42:52:4f Vendor PN 57-0000075-01 Vendor 0.002 (mAmps) TX Power 0.1 (uWatts) RX Power 0.1 (uWatts) See Also - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 48
Linecard number. Defaults There are no default configurations for this line card number 0: switch#show media linecard 0 meters) Length Cu 0 (units 1 meter) Vendor Name BROCADE Vendor OUI 42:52:4f Vendor PN 57-0000075-01 Vendor (mAmps) TX Power 0.1 (uWatts) RX Power 0.1 (uWatts) - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 49
a summary of CPU usage by all processes. Defaults There are no default configurations for this command. Command Privileged EXEC mode Modes Description Use this command to display information about the active processes in the switch and their corresponding CPU utilization statistics. Usage There - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 50
Defaults There are no default configurations for this command. Command Privileged EXEC mode Modes Description Use this command to view memory usage information based by individual processes: switch#show processes memory % See Also none 32 Converged Enhanced Ethernet Command Reference 53-1001347- - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 51
interface configuration. Displays the LLDP configuration. Displays the Remote Monitoring Protocol (RMON) configuration. Displays the switch configuration. Defaults There are no default configurations for this command. Command Privileged EXEC mode Modes Description Use this command to display the - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 52
file. Synopsis show startup-config Operands none Defaults There are no default configurations for this command. Command Privileged EXEC displays if there are no entries in the startup configuration file, for example switch#show startup-config % No Startup-config • Use the write memory command to - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 53
. Synopsis show system Operands none Defaults There are no default configurations for this command. Command Privileged Burned In MAC Management IP Status : switch : Online : 76.6 : 8 : 24 : 18:28:27 up 4:09 : v6.1.2 : yes : 00:05:1E:76:42:00 : 10.35.155.204 : UP -- Power Supplies -PS0 is OK - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 54
for troubleshooting: switch#show tech-support date Thu Feb 19 18:30:13 UTC 2009 show version Fabric Operating System Software Fabric Operating System Version: 6.1 Copyright (c) 1995-2008 Brocade Communications Systems, Inc. Build Time: 03:35:17 Feb 18, 2009 switch uptime: 04:11:09 Firmware - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 55
all users currently logged into the switch. Synopsis show users Operands none Defaults There are no default configurations for this command. Command numbers. Displays how long the session has been idle. Displays the IP address of the user. Displays the user name of all users logged in. Converged - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 56
and software. Synopsis show version Operands none Defaults There are no default configurations for this command. Command Privileged 35:17 Feb 18, 2009 E209 uptime: 04:14:43 Firmware name: v6.1.2 Switch Model Name: Brocade 8000 Control Processor: Freescale Semiconductor 8548E with 1016 MB of - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 57
The default length is 24. Command Privileged EXEC mode Modes Description Use this command to set the number of lines to display on the screen. Usage If 0 (zero), the switch does not pause between screens of output. Guidelines Examples To set the number of lines to display on the screen to - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 58
terminal. Synopsis terminal monitor terminal no monitor Operands none Defaults The terminal monitor option is disabled. Command Privileged EXEC mode on a terminal: switch#terminal monitor To disable the display of the RASlog and the debug outputs on a terminal: switch#terminal no monitor See - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 59
write erase Removes the startup configuration from the switch. Synopsis write erase Operands none Defaults There are no default configurations for this command. Command Privileged EXEC mode Modes Description Use this command to remove a startup configuration. Usage There are no usage - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 60
startup configuration file. Synopsis write memory Operands none Defaults There are no default configurations for this command. Command Privileged EXEC command. Guidelines Examples To write configuration data to a file: switch#write memory Overwrite the startup config file (y/n): y Building - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 61
VLAN interface. Synopsis fcf forward no fcf forward Operands none Defaults FCF forwarding is disabled. Command Interface VLAN mode Modes Description Examples To enable FC forwarding on a VLAN interface: switch(config)#interface vlan 777 switch(conf-if-vl-777)#fcf forward See Also interface - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 62
no interface vlan vlan_id Operands vlan_id Specifies the VLAN interface to configure. The range of valid values is 1-3583. Defaults VLAN 1 is predefined on the switch. Command Global configuration mode Modes Description Use this command to configure a VLAN interface. Use the no interface vlan - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 63
this command. Guidelines Examples To display information for a 10 Gbps Ethernet interface: switch#show interface tengigabitethernet 0/1 Interface name Switchport mode Ingress filter Acceptable frame types Default Vlan Active Vlans Inactive Vlans : TenGigabitEthernet 0/7 : access : enable : all - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 64
are no usage guidelines for this command. Guidelines Examples To show information on a VLAN: switch#show vlan 1 VLAN Name State Ports (u)-Untagged, (t)-Tagged (c)-Converged 1 default ACTIVE Te 0/0(t) Te 0/4(t) Te 0/5(t) Te 0/8(t) Te 0/10(t) Te 0/11(c) Po 1(t) Po 63(t) See Also - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 65
256. tengigabitethernet Specifies a valid 10 Gbps Ethernet interface. slot Specifies a valid slot number. port Specifies a valid port number vlan vlan_id Specifies the VLAN to display. The range of valid values is 1-3583. Defaults There are no default for group 1: switch#show vlan classifier - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 66
switching characteristics of the Layer 2 interface to the defaults. Synopsis switchport no switchport Operands none Defaults By default, all Layer 2 interfaces are mapped to default Layer 2 mode: switch(conf-if-te-0/1)#switchport To remove an interface from Layer 2 mode: switch(conf-if-te-0/1)#no - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 67
tagged packets. Use the no switchport access vlan command to set the PVID to the default VLAN 1. Usage There are no usage guidelines for this command. Guidelines Examples To set the Layer 2 interface PVID to 100: switch(conf-if-te-0/19)#switchport access vlan 100 See Also show vlan brief, show - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 68
Layer 2 interface. The range of valid values is 2-3583. Defaults The default native VLAN for a converged interface is 1. Command Interface configuration mode add 100 To remove the tagged VLAN 100 from the interface: switch(conf-if-te-0/19)#switchport converged allowed vlan remove 100 See Also - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 69
There are no defaults for this command. Command Interface configuration mode Modes Description Use this command to set the mode of the Layer 2 interface. Usage There are no usage guidelines for this command. Guidelines Examples To set the mode of the interface to access: switch(conf-if-te - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 70
default configurations for this command. Command Interface configuration mode Modes Description Use this command to add or remove tagged VLANs on a Layer 2 interface. Usage There are no usage guidelines for this command. Guidelines Examples To set the tagged VLAN on an interface to 100: switch - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 71
values is 1-16. Specifies which VLAN interface to activate. The range of valid values is 1-3583. Defaults There are no default configurations for command. Guidelines Examples To activate VLAN classifier group 1 for VLAN 5: switch-cmsh(conf-if-te-0/10)#vlan classifier activate group 1 vlan 5 See - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 72
deleted. The range of valid values is 1-16. add rule number Specifies a rule is to be added. The range of valid values is 1-256. delete rule number Specifies a rule is to be deleted. The range of valid values is 1-256. Defaults There are no default configurations for this command. Command Global - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 73
|arp| fcoe | fip| ip] [encap ethv2 | nosnapllc | with SNA frames. Defaults There are no default configurations for this be managed separately. Up to 256 VLAN classifiers can be provisioned. switch(config)#vlan classifier rule 2 proto fcoe encap ethv2 To create a MAC-based VLAN classifier rule: switch - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 74
3 vlan classifier rule 56 Converged Enhanced Ethernet Command Reference 53-1001347-01 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 75
number Specifies the slot number of the linecard. For the Brocade 8000 switch, the slot number is always 0 (zero). Description Use this command to clear statistics on one or on all interfaces. Defaults There are no default configurations for this command. Command Privileged EXEC mode Modes User - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 76
interface. The maximum number of characters is 64. Defaults There are no default configurations for this command. Command Interface Guidelines Examples To set the string describing tengigabitethernet interface 0/1: switch(conf-if-te-0/1)#description converged_101 See Also none 58 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 77
The range of valid values is 1-63. vlan vlan_id Specifies the VLAN number. The range of valid values is 1-3583. Defaults There are no default configurations for this command. Command Global configuration mode Modes Description Use this command to create or enter the interface configuration mode - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 78
the size of the maximum transmission unit (MTU) of an interface. The allowed MTU size is 1522-9208 bytes. Defaults By default, all 10 Gbps Ethernet interfaces use a default MTU of 2500 bytes. Command Interface configuration mode Modes Description Use this command to specify the MTU on the - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 79
Defaults There are no default configurations Ethernet interface 0/1: switch#show interface tengigabitethernet 2500 bytes LineSpeed: 10000 Mbit, Duplex: Full Flowcontrol rx: on, tx: on Last 0 bytes Unicasts: 0, Multicasts: 0, Broadcasts: 0 64-byte pkts: 0, Over 64-byte pkts: 0, Over 127-byte pkts: 0 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 80
information for all interfaces: switch#show interface switchport Interface name Switchport mode Ingress filter Acceptable frame types Default Vlan Active Vlans Inactive types Default Vlan Active Vlans Inactive Vlans : TenGigabitEthernet 0/20 : trunk : enable : vlan-tagged only : 0 : 1 : - show ip - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 81
is 1-3583. Defaults There are no default configurations for this command. Command EXEC mode Modes Description Use this command to display IP interface status and the interfaces in the summary format: switch#show ip interface brief Interface IP-Address ======== ========== Port-channel 10 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 82
4 show ip interface See Also TenGigabitEthernet 0/13 TenGigabitEthernet 0/14 TenGigabitEthernet 0/15 TenGigabitEthernet 0/16 TenGigabitEthernet 0/17 TenGigabitEthernet 0/18 up down up down up up up up up down down down 64 Converged Enhanced Ethernet Command Reference 53-1001347-01 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 83
no usage guidelines for this command. Guidelines Examples To disable an interface: switch(conf-if-te-0/1)#shutdown To enable an interface: switch(conf-if-te-0/1)#no shutdown See Also interface, show ip interface, show interface shutdown 4 Converged Enhanced Ethernet Command Reference 65 53 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 84
4 shutdown 66 Converged Enhanced Ethernet Command Reference 53-1001347-01 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 85
such as FCoE priority, and Priority Flow Control (PFC) pause. Use the no advertise dcbx-fcoe-app-tlv command to return to the default setting. Usage There are no usage guidelines for this command. Guidelines Examples none See Also advertise dot1-tlv, advertise dot3-tlv, advertise optional - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 86
to any attached device the FCoE status of the logical link. Use the no advertise dcbx-fcoe-logical-link-tlv command to return to the default setting. Usage There are no usage guidelines for this command. Guidelines Examples none See Also advertise dcbx-fcoe-app-tlv, advertise dcbx fcoe-app-tlv - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 87
mandatory Data Center Bridging eXchange protocol (DCBX) Type, Length, Values (TLVs). Use the no advertise dcbx-tlv command to return to the default setting. Usage There are no usage guidelines for this command. Guidelines Examples none See Also advertise dot1-tlv, advertise dot3-tlv, advertise - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 88
to any attached device IEEE 802.1 organizationally specific Type, Length, Value (TLV). Use the no advertise dot1-tlv command to return to the default setting. Usage There are no usage guidelines for this command. Guidelines Examples none See Also advertise dot3-tlv, advertise dcbx-tlv, advertise - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 89
to any attached device IEEE 802.3 organizationally specific Type, Length, Value (TLV). Use the no advertise dot3-tlv command to return to the default setting. Usage There are no usage guidelines for this command. Guidelines Examples none See Also advertise dot1-tlv, advertise dcbx-tlv, advertise - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 90
the system firmware version and the current image running on the system. system-name Specifies the name of the system. Defaults Advertise TLVs. Use the no advertise optional-tlv command to return to the default setting. Usage There are no usage guidelines for this command. Guidelines Examples - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 91
valid slot number. port Specifies a valid port number. Defaults There are no default configurations for this command. Command Privileged EXEC mode Modes . Examples To clear the LLDP information for all interfaces: switch#clear lldp neighbors See Also show lldp neighbors Converged Enhanced - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 92
valid slot number. port Specifies a valid port number. Defaults There are no default configurations for this command. Command Privileged EXEC mode Modes Examples To clear all the LLDP statistics for all interfaces: switch#clear lldp statistics See Also show lldp statistics 74 Converged Enhanced - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 93
. tx Turns on debugging for only transmitted LLDP packets. Defaults By default, debugging is not turned on. Command Privileged EXEC mode Modes packets on 10 Gbps Ethernet interface 0/1: switch#debug lldp packet interface tengigabitethernet 0/1 both switch#show debug lldp LLDP debugging status: - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 94
Operands line Characters describing the LLDP protocol. Defaults There are no default configurations for this command. Command Protocol LLDP Examples To set the strings describing LLDP: switch(conf-lldp)#description Brocade-LLDP See Also none 76 Converged Enhanced Ethernet Command Reference - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 95
LLDP hello messages. Use the no hello command to return to the default setting. Usage There are no usage guidelines for this command. Guidelines interval to 10 seconds between the transmissions: switch#configure terminal switch (config) #protocol lldp switch(conf-lldp)#hello 10 See Also none - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 96
The default is auto. Command Interface configuration mode Modes Description Use this command to specify which version of the DCBX protocol to use. Usage There are no usage guidelines for this command. Guidelines Examples To specify which DCBX version to use: switch(conf-if-te-0/1)#lldp dcbx - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 97
on the interface. Synopsis lldp disable no lldp disable Operands none Defaults By default, LLDP is enabled at both the global and interface levels. . Guidelines Examples To disable LLDP on the interface. switch(conf-if-te-0/1)#lldp disable See Also none Converged Enhanced Ethernet Command Reference - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 98
returns to the default setting. Usage There are no usage guidelines for this command. Guidelines Examples To set the priorities on which FCoE traffic will be allowed: switch(conf-if-te-0/1)#lldp fcoe-priority-bits 0xff See Also protocol lldp 80 Converged Enhanced Ethernet Command Reference - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 99
Operands name Specifies the profile name. Defaults If the parameters are not defined in the profile, the default values are used. Command Interface configuration used. Examples To apply an LLDP profile on an interface: switch(conf-if-te-0/1)#lldp profile test See Also protocol lldp Converged - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 100
modes are enabled. Command Protocol LLDP configuration mode Modes Description Use this command to set the LLDP mode on the switch. Use the no mode command to return to the default setting. Usage There are no usage guidelines for this command. Guidelines Examples To enable only the transmit mode - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 101
neighbor as dead. Use the no multiplier command to return to the default setting. Usage There are no usage guidelines for this command. Guidelines Examples To set the number of consecutive misses: switch(conf-lldp)#multiplier 2 See Also hello Converged Enhanced Ethernet Command Reference 83 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 102
value is a maximum of 32 characters. Defaults none Command Protocol LLDP configuration default global profile is used until you create a valid profile. Up to 64 profiles can be created. Examples To create a profile named test: switch(conf-lldp)#profile test To delete a profile named test: switch - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 103
to the parameters. Use the no protocol lldp command to return to the default setting. Usage There are no usage guidelines for this command. Guidelines Examples To clear all LLDP configurations: switch(config)#no protocol lldp See Also none Converged Enhanced Ethernet Command Reference 85 53 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 104
Displays the LLDP debugging status on the switch. Synopsis show debug lldp Operands none Defaults There are no default configurations for this command. Command EXEC mode Modes Description Use this command to display the LLDP debugging status on the switch. Usage There are no usage guidelines - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 105
a valid port number. Defaults There are no default configurations for this command. information for a selected interface: switch#show lldp interface tengigabitethernet 0/0 LLDP Link Prim DCBX FCoE Priority Bits: 0x8 Port ID IEEE DCBX DCBX FCoE Logical Link Brocade Link See Also none Converged - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 106
System Description: Fibre Channel Switch. System Capabilities: Switching Routing System Capabilities Enabled: Switching Link Prim: 257 Remote Protocols Advertised: Multiple Spanning Tree Protocol Remote VLANs Configured: VLAN ID: 1 VLAN Name: default AutoNego Support: Supported Not Enabled AutoNego - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 107
Protocol Vlan Flag: Supported Not enabled Port & Protocol Vlan Id: 0 Link Aggregation Port Id: 0 Max Frame Size: 2500 Management Address: 10.32.152.21 ( : 0 MaxVersion: 0 EN: 1 Will: 0 Err: 0 Logic Link Status: Up switch# none Converged Enhanced Ethernet Command Reference 89 53-1001347-01 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 108
slot number. port Specifies a valid port number. Defaults There are no default configurations for this command. Command EXEC mode Modes Description To display LLDP statistics on the specified interface: switch#show lldp statistics interface tengigabitethernet 0/8 LLDP Interface statistics - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 109
The valid value is a maximum of 50 characters. Defaults There are no default configurations for this command. Command Protocol LLDP mode. Modes set the global system description specific to LLDP: switch(conf-lldp)#system-description Brocade See Also system-name Converged Enhanced Ethernet Command - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 110
The valid values is a maximum of32 characters. Defaults By default, the host name from the switch is used. Command Protocol LLDP configuration mode Modes specify a system name for the LLDP: switch(conf-lldp)#system-name Brocade See Also system-description 92 Converged Enhanced Ethernet Command - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 111
based LAG. Specifies the Brocade proprietary hardware-based trunking. Defaults By default aggregation groups can be created per switch when the type is set to brocade. • A maximum of four links 2, and links 16-23 belong to port-channel 3. • For the standard type, a maximum of 16 links can be - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 112
6 channel-group See Also switch(conf-if)#channel-group 4 mode active interface port-channel 94 Converged Enhanced Ethernet Command Reference 53-1001347-01 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 113
to clear the LACP counters per specified channel-group. Usage There are no default configurations for this command. Guidelines Examples To clear the LACP counters for a specific port-channel: switch#clear lacp 10 counters See Also show lacp counters Converged Enhanced Ethernet Command Reference - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 114
this command to clear the LACP counters for all port-channels. Usage There are no default configurations for this command. Guidelines Examples To clear the counters for all port-channels: switch#clear lacp counters See Also show lacp 96 Converged Enhanced Ethernet Command Reference 53-1001347 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 115
interface debugging. event Turns on event debugging. nsm Turns on Network Services Module (NSM) debugging. pdu Turns on PDU debugging. rx all Turns the trace level number. The range of valid values is 1-7. Defaults By default, debugging is not turned on. Command Privileged EXEC mode Modes - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 116
6 debug lacp Examples See Also To enable debugging of LACP PDUs for transmitted and received packets on all interfaces: switch#debug lacp pdu tx all switch#debug lacp pdu rx all switch#show debug lacp LACP rx debugging is on LACP tx debugging is on show debug lacp 98 Converged Enhanced Ethernet - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 117
LACP system priority. The range of valid values is 1-65535. Defaults The default system-priority value is 32768. Command Global configuration mode Modes system-priority to 68: switch(config)#lacp system-priority 68 To clear the configured LACP system-priority: switch(config)#no lacp system- - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 118
Description Use this command to set the short timeout value for Brocade trunks or to set the long timeout value for standard trunks. Use the no lacp timeout command to return to the default value. Usage If the LACP_timeout bit (encoded in Actor_State and Partner_State fields) is set to 1, the short - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 119
to display. The range of valid values is 1-63. Defaults There are no default configurations for this command. Command EXEC mode Modes Description Use Po 10 1000000 Te 0/1 65 0 0 0 Te 0/2 64 0 0 0 Te 0/3 64 0 0 0 Te 0/4 0 0 0 0 switch# Pckt err Sent Recv 0 0 0 0 0 0 0 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 120
priority information. Synopsis show lacp sys-id Operands none Defaults There are no default configurations for this command. Command EXEC mode Modes addresses associated with the system. Examples To display the local system ID: switch#show lacp sys-id % System 8000,00-05-1e-76-1a-a6 See - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 121
LAG interfaces are called port-channels. Defaults There are no default configurations for this command. Command EXEC mode port-channels are displayed. Guidelines Examples To display information for port-channel 10: switch#show port-channel 10 % Aggregator Po 10 0 Admin Key: 0010 - Oper Key - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 122
6 show port-channel 104 Converged Enhanced Ethernet Command Reference 53-1001347-01 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 123
The default aging time is 300 seconds. Command Global configuration mode Modes Description Use this command to set the aging time or to add static addresses to the MAC address table. Usage The vlan keyword is mandatory because the switch only supports independent VLAN learning (IVL). Guidelines - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 124
7 mac-address-table See Also To set the aging time to 10 minutes: switch(config)#mac-address-table aging-time 600 show mac address-table static 106 Converged Enhanced Ethernet Command Reference 53-1001347-01 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 125
vlan vlan_id ] Operands address mac-address Specifies a 48-bit MAC address. The valid format is H.H.H (available in The range of valid values is 1-3583. Defaults No static addresses are configured. Command EXEC mode MAC address in the table: switch#show mac-address-table address 0011.2222.3333 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 126
To display the aging time for a specific MAC address table: switch#show mac-address-table aging-time MAC Aging-time : 300 seconds To display a dynamic MAC address table: switch#show mac-address-table dynamic VlanId Mac-address Type State 100 0011 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 127
VLAN number. The range of valid values is 1-3583. Defaults There are no default configurations for this command. Command Privileged EXEC mode Modes Description counters supported per port group. Example To clear counters for the configured MAC access list named test on an interface: switch#clear - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 128
matching the rule. Defaults By default, no MAC ACLs based on the source and destination MAC addresses and the protocol type. You can also enable counters for a specific rule. There are 255 ACL counters supported and to enable the counting of packets: switch(conf-macl-ext)#deny 0022.3333.4444 0022. - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 129
deny (extended ACLs) 8 See Also switch(conf-macl-ext)#no deny 0022.3333.4444 0022.3333.5555 ipv4 mac-access-list extended, mac-access-list standard, permit Converged Enhanced Ethernet Command Reference 111 53-1001347-01 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 130
By default, no MAC ACLs are configured. Command Feature Access Control List Configuration mode Modes Description Use this command to configure rules to match and to drop traffic based on the source MAC address. You can also enable counters for a specific rule. There are 255 ACL counters supported - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 131
access list. The maximum character limit is 64. Command Global configuration mode Modes Description Use is already created, this command puts the switch in the extended MAC access-list configuration mode list. Extended ACLs allow you to filter traffic based on the following: • Source MAC address • - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 132
list. The maximum character limit is 64. Command Global configuration mode Modes Description Use is already created, this command puts the switch in the standard MAC access-list configuration mode list. Standard ACLs allow you to filter traffic based on the source MAC address. You can apply - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 133
extended MAC access list. Specifies to filter inbound packets only. Default There are no access lists applied to the interface. Command an interface with a MAC ACL applied, the switch checks the rules in the ACL. If any of the rules match, the switch permits or drops the packet, according to the - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 134
matching the filter rule. Defaults By default, no MAC ACLs are based on the source and destination MAC addresses, and the protocol type. You can also enable counters for a specific rule. There are 255 ACL counters supported the counting of packets: switch(conf-macl-ext)#permit 0022.3333.4444 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 135
permit (extended ACLs) 8 See Also To delete a filter rule in a MAC extended ACL: switch(conf-macl-ext)#no permit 0022.3333.4444 0022.3333.5555 ipv4 mac-access-list extended, mac-access-list standard, no seq Converged Enhanced Ethernet Command Reference 117 53-1001347-01 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 136
default, no MAC ACLs are configured. Command Feature Access Control List Configuration mode Modes Description Use this command to configure rules to match and to permit traffic based on the source MAC address. You can also enable counters for a specific rule. There are 255 ACL counters supported - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 137
rules. The range of valid values is 1-65535. Defaults There are no default configurations for this command. Command Privileged EXEC mode of an existing access list. Example To reorder the rules in a MAC ACL: switch#show running-config access-list mac test ! mac access-list standard test seq - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 138
Enables the counting of the packets matching the rule. Defaults By default, no MAC ACLs are configured. Command Feature Access traffic based on the source and destination MAC addresses, and the protocol type. You can also enable counters for a specific rule. There are 255 ACL counters supported per - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 139
0022.3333.4444 to the destination MAC address 0022.3333.5555 and to enable the counting of packets: switch(conf-macl-ext)#seq 100 deny 0022.3333.4444 0022.3333.5555 ipv4 count switch(conf-macl-ext)#seq 1000 permit 0022.3333.4444 0022.3333.5555 ipv4 count To delete a rule from - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 140
packets matching the rule. Defaults By default, no MAC ACLs are based on source and destination MAC address and protocol type. You can also enable counters for a specific rule. There are 255 ACL counters supported of packets: switch(conf-macl-std)#seq 100 deny 0022.3333.4444 count switch(conf-macl- - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 141
number. The range of valid values is 1-3583. Defaults There are no default configurations for this command. Command EXEC mode Modes Description Use To display the current MAC ACL mapping for interface VLAN 100: switch#show mac access-group interface vlan 100 Interface Vl 100 Inbound access - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 142
There are no default configurations for this command. Command EXEC mode Modes Description Use this command to display the active rules on the switch and whether those rules have counters enabled. Examples To display the statistics for standard and extended MAC ACL applied on two interfaces - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 143
to return to the default settings. Usage This switch#configure terminal switch(config)#protocol spanning-tree stp switch(conf-stp)#bridge-priority 8192 switch#configure terminal switch(config)#protocol spanning-tree rstp switch(conf-rstp)#bridge-priority 8192 switch#configure terminal switch - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 144
| enable] Operands disable enable Disables Cisco interoperability for the Multiple Spanning Tree Protocol (MSTP) switch. Enables Cisco interoperability for the MSTP switch. Defaults Cisco interoperability is disabled. Command Protocol Spanning Tree MSTP mode Modes Description Use this command - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 145
slot number. port Specifies a valid port number. Defaults There are no default configurations for this command. Command Privileged EXEC mode interface: switch#clear spanning-tree counter interface tengigabitethernet 0/1 To clear spanning-tree counters for port-channel 23: switch#clear spanning - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 146
the slot number. port Specifies the port number. Defaults By default debugging is not turned on. Command Privileged EXEC mode interface 0/1: switch#debug spanning-tree bpdu rx interface tengigabitethernet 0/1 switch#debug spanning-tree bpdu tx interface tengigabitethernet 0/1 switch#show debug - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 147
. Synopsis error-disable-timeout enable Operands none Defaults There are no default configurations for this command. Command Protocol Spanning , the port remains in the disabled state unless the port is enabled manually. This command allows you to enable the interface from the disabled state. - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 148
to time out. The range of valid values is 10-1000000. Defaults The default is 300 seconds. The timeout feature is disabled. Command Protocol Spanning command. Guidelines Examples To set the timeout value to 10 seconds: switch(conf-rstp)#error-disable-timeout interval 10 See Also error-disable- - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 149
listening states. The range of valid values is 4-30. Defaults The default is 15 seconds. Command Protocol Spanning Tree mode Modes Description blocking state to prevent a loop. • Blocking - An interface that can cause a switching loop, no user data is sent or received, but it might go to the - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 150
BPDUs sent on an interface. The range of valid values is 1-10. Defaults The default is 2 seconds. Command Protocol Spanning Tree mode Modes Description Use this Examples To configure spanning-tree bridge hello time to 5 seconds: switch(conf-stp)#hello-time 5 See Also forward-delay, max-age - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 151
61440. The priority values can be set only in increments of 4096. Defaults The default priority value is 32768. Command Protocol Spanning Tree MSTP mode Modes Description to an MTSP instance: switch(conf-mstp)#instance 1 vlan 2, 3 switch(conf-mstp)#instance 2 vlan 4-6 switch(conf-mstp)#instance 1 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 152
Protocol interface maximum-age. The range of valid values is 6-40. Defaults The default is 20 seconds. Command Protocol Spanning Tree mode Modes Description Use + 1) Examples To configure the maximum-age to 10 seconds: switch(conf-rstp)#max-age 10 See Also hello-time, forward delay 134 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 153
BPDU will be valid. The range of valid values is 1-40. Defaults The default is 20 hops. Command Protocol Spanning Tree MSTP mode Modes Description Use number of maximum hops to 25 for all MSTPs: switch(config)#protocol spanning-tree mstp switch(conf-mstp)#max-hops 25 See Also show spanning-tree - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 154
The default path-cost is standard. Command Protocol Spanning Tree mode Modes Description Use this command to set the path-cost behavior for the port-channel. Usage There are no usage guidelines for this command. Guidelines Examples To set the behavior for the path-cost to custom: switch(conf - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 155
Rapid Spanning Tree (RSTP). Specifies the Spanning Tree Protocol (STP). Defaults By default, STP is not enabled. STP is not required in a loop another form. Examples To enable the Spanning Tree Protocol: switch(config)#protocol spanning-tree stp See Also show spanning-tree Converged Enhanced Ethernet - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 156
-name Assigns a name to an MSTP region. Defaults There are no default configurations for this command. Command Protocol Spanning Tree MSTP 32 characters and is case-sensitive. Guidelines Examples To assign a name to an MSTP region named brocade1: switch(config)#protocol spanning-tree mstp switch - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 157
number. Use the no revision command to return to the default setting. Usage There are no usage guidelines for this command. Guidelines Examples To set the configuration revision to 1: switch(config)#protocol spanning-tree mstp switch(conf-mstp)#revision 1 See Also region, show spanning-tree - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 158
There are no default configurations for this command. Command EXEC mode Modes Description Use this command to display all STP information. Usage There are no usage guidelines for this command. Guidelines Examples To display all STP information: switch#show spanning-tree Spanning-tree Mode - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 159
show spanning-tree 9 See Also Designated Port Id: 0; CIST Priority: 128 Designated Bridge: 0000.0000.0000.0000 CIST Port Hello Time: 2 Number of forward-transitions: 0 Version Multiple Spanning Tree Protocol - Received None - Send MSTP Edgeport: off; AutoEdge: no; AdminEdge: no; EdgeDelay: 3 sec - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 160
Protocol. Synopsis show spanning-tree brief Operands none Defaults There are no default configurations for this command. Command EXEC mode Modes To display the status and parameters of the Spanning Tree Protocol: switch#show spanning-tree brief Spanning-tree Mode: Rapid Spanning Tree Protocol - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 161
number. port Specifies a valid port number. Defaults There are no default configurations for this command. Command EXEC mode Modes port. Examples To display information on a 10 Gbps Ethernet interface: switch#show spanning-tree interface tengigabitethernet 0/0 Spanning-tree Mode: Rapid Spanning - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 162
Synopsis show spanning-tree mst brief Operands none Defaults There are no default configurations for this command. Command EXEC mode Examples To display the status and parameters of the MSTP instance information: switch#show spanning-tree mst brief Spanning-tree Mode: Multiple Spanning Tree - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 163
are no default configuration for this command. Command EXEC mode Modes Description Use this command to display details on a specified interface for the MSTP instance running. Usage There are no usage guidelines for this command. Guidelines Examples To display MSTP information on the switch in - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 164
9 show spanning-tree mst detail Designated Bridge: 0000.0000.0000.0000 CIST Port Hello Time: 2 Number of forward-transitions: 0 Version Multiple Spanning Tree Protocol - Received None - Send MSTP Edgeport: off; AutoEdge: no; AdminEdge: no; EdgeDelay: 3 sec Configured Root guard: off; Operational - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 165
show spanning-tree mst detail 9 See Also Link-type: point-to-point Received BPDUs: 0; Sent BPDUs: 0 MSTI details show spanning-tree mst interface, show spanning-tree mst instance Converged Enhanced Ethernet Command Reference 147 53-1001347-01 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 166
no default configurations for this command. Command EXEC mode Modes Description Use this command to display information on a specified instance of the MSTP. Usage There are no usage guidelines for this command. Guidelines Examples To display information on MSTP instance 1: switch#show spanning - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 167
which to display information for the MSTP instance. Defaults There are no default configurations for this command. Command EXEC mode command. Guidelines Examples To display information for the MSTP interface: switch#show spanning-tree mst interface tengigabitethernet 0/0 Spanning-tree Mode: - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 168
topology and is not enabled by default. Command Protocol Spanning Tree mode Modes Description Use this command to disable the MSTP, RSTP, or STP protocol globally. Usage This command has no usage guidelines. Guidelines Examples To disable STP globally: switch(config)#protocol spanning-tree rstp - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 169
-tree autoedge no spanning-tree autoedge Operands none Defaults Auto detection is not enabled. Command Interface configuration (BPDU) is received. Guidelines Examples To enable automatic edge detection: switch(conf-if-te-0/1)#spanning-tree autoedge See Also protocol spanning-tree Converged - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 170
The default path cost is 200000000. Command Interface configuration mode Modes Description Use this command to configure the path cost for spanning-tree calculations. Usage Lower path cost indicates a greater chance of becoming root. Guidelines Examples To set the port cost to 128: switch(conf - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 171
for the port. Guards the port against the reception of BPDUs. Defaults Edge port is disabled. Command Interface configuration mode Modes Description Use this the forwarding state: switch(conf-if-te-0/1)#spanning-tree edgeport To set the edgeport BPDU filter for the port: switch(conf-if-te-0/1)# - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 172
is allowed to be the spanning-tree root port or the path-to-the root for the switch. Synopsis spanning-tree guard root no spanning-tree guard root Operands none Defaults Guard root is disabled. Command Interface configuration mode Modes Description Use this command to enable the guard - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 173
seconds Sets the interval between the hello Bridge Protocol Data Units (BPDUs) sent by the root switch configuration messages. The range of valid values 1-10. Defaults The default is 2 seconds. Command Interface configuration mode Modes Description Use this command to set the interval time - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 174
20000000. Specifies the port priority for a bridge in increments of 16. The range of valid values is 0-240. Specifies to the topology change notifications from a port. Defaults The default path-cost value is 2000 on a 10 1 with the cost of 40000: switch(conf-if-te-0/1)#spanning-tree instance 1 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 175
Use this command to specify a link type for the Spanning Tree Protocol. Usage This command overrides the default setting of the link type. Guidelines Examples To specify the link type as shared: switch(conf-if-te-0/0)#spanning-tree link-type shared See Also spanning-tree link-type shared, no - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 176
for the port. Guards the port against the reception of BPDUs. Defaults Port Fast is disabled. Command Interface configuration mode Modes Description Use the forwarding state: switch(conf-if-te-0/1)#spanning-tree portfast To set the Port Fast BPDU filter for the port: switch(conf-if-te-0/1)# - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 177
Use the no spanning-tree priority command to return to the default setting. Usage There are no usage guidelines for this command. Guidelines Examples To configure the port priority to 16: switch(conf-if-te-0/1)#spanning-tree priority 16 See Also spanning-tree cost, show spanning-tree Converged - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 178
. Use the no spanning-tree restricted-role command to return to the default setting. Usage There are no usage guidelines for this command. Guidelines Examples To configure the port from becoming a root port: switch(conf-if-te-0/1)#spanning-tree restricted-role See Also show spanning-tree 160 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 179
restricted-tcn no spanning-tree restricted-tcn Operands none Defaults The restricted TCN is disabled. Command Interface configuration mode command. Guidelines Examples To restrict the TCN on a specific interface: switch(conf-if-te-0/1)#spanning-tree restricted-tcn See Also show spanning-tree - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 180
tree shutdown no spanning-tree shutdown Operands none Defaults Spanning tree is not enabled. Command Interface configuration switch(config)#interface tengigabitethernet 0/1 switch(conf-if-te-0/1)#spanning-tree shutdown To enable spanning tree on VLAN 1002: switch(config)#interface vlan 1002 switch - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 181
spanning-tree tc-flush-standard no spanning-tree tc-flush-standard Operands none Defaults MAC address flushing is enabled. Command Global configuration mode Modes Description Use this command to flush the MAC address based on the optimal scheme. Use the no spanning-tree tc-flush-standard command - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 182
pausing for 1 second. The range of valid values is 1-10. Defaults The default is 6. Command Protocol Spanning Tree MSTP mode Modes Description Use this command . Use the no transmit-holdcount command to return to the default setting. Usage There are no usage guidelines for this command. Guidelines - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 183
variable must be in the SNMP OID format, for example, 1.3.6.1.2.1.16.1.1.1.5.65535. The object type must be a counter32. interval seconds Specifies identity of the owner. The maximum number of characters is 32. Defaults There are no alarms configured. Command Global configuration mode Modes - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 184
10 rmon alarm See Also switch(config)#rmon alarm 100 1.3.6.1.2.1.16.1.1.1.5.65535 interval 5 absolute rising-threshold 10000 event 100 falling-threshold 1000 event 101 owner admin rmon event, show rmon 166 Converged Enhanced Ethernet Command Reference 53-1001347-01 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 185
valid values is 1-65535. Specifies the identity of the owner. Defaults The collection of RMON statistics is not enabled. Command Interface configuration admin on 10 Gbps Ethernet interface 0/1: switch(config)#interface tengigabitethernet 0/1 switch(conf-if-te-0/1)#rmon collection stats 2 owner - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 186
The maximum number of characters is 32. Specifies the SNMP community or string name to identify this trap. Defaults There are no events configured. Command for this command. Guidelines Examples To configure an RMON event: switch(config)#rmon event 2 log description "My Errorstoday" owner gjack - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 187
: TenGigabitEthernet 0/0 Receive Statistics: 218903 packets, 14015626 bytes, 0 packs dropped Multicasts: 218884, Broadcasts: 18 Under-size : 0, Jabbers: 0, CRC: 0 Fragments: 0, Collisions: 0 64 byte pkts: 218722, 65-127 byte pkts: 174 128-255 byte pkts: 0, 256-511 byte pkts: 6 512-1023 byte pkts - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 188
10 show rmon See Also Owner: RMON_SNMP Status: ok(1) To display the RMON events: switch#show rmon events event Index = 4 Description "My Description" Event type Log & SnmpTrap Event community name admin Last Time Sent = 00:00:00 Owner admin rmon - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 189
CEE map must be removed before a new one can be applied. Defaults There is no CEE Provisioning applied on an interface. Command Interface should exist on the switch. Guidelines Examples To apply a CEE map on an interface: switch(conf-if-te-0/1)#cee demo Because the switch does not allow - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 190
valid values is 1-100. Defaults The default CEE map precedence value is only a single scheduler policy supported across the entire system. policy. The global scheduler policy is based on the CEE Map with the highest a CEE map: switch(config)#cee-map test To delete a CEE map: switch(config)#no cee-map - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 191
Enables the Priority-based Flow Control (PFC) for each priority that gets mapped to the Priority Group. Defaults There is no default value for the 1 50 Y SAN N LAN See Also switch(config)#cee-map test switch(conf-ceemap)#priority-group-table 0 weight 50 pfc switch(conf-ceemap)#priority- - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 192
ID for all packets with CoS 6. Sets the Priority Group ID for all packets with CoS 7. Defaults The default CEE Priority mapping table matches the IEEE 802.1Q recommendation for systems supporting eight traffic classes. The 802.1Q maps CoS 0 (best effort) to Strict Priority Traffic Class 1 (PGID - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 193
priority-table 11 See Also switch(config)#ceemap test switch(conf-ceemap)#priority-table 1 1 0 0 1 1 1 15.0 cee, cee-map, priority-group-table Converged Enhanced Ethernet Command Reference 175 53-1001347-01 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 194
Service (CoS) value. Synopsis qos cos value no qos cos Operands value Specifies the CoS value. The range of valid values is 0-7. Defaults The default the interface CoS value to 2: switch(conf-if-te-0/2)#qos cos 2 To return the interface CoS value to the default: switch(conf-if-te-0/2)#no qos cos - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 195
the name of the CoS mutation map. Defaults There is no explicit CoS-to-CoS mutation QoS map applied; by default the inbound CoS equals the outbound CoS. CoS-to-CoS mutation QoS map on the interface: switch(conf-if-te-0/1)#qos cos-mutation test To remove the CoS-to-CoS mutation QoS - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 196
before a new one can be applied. Defaults There is no explicit CoS-to-Traffic Class QoS IEEE 802.1Q recommendations for systems supporting eight Traffic Classes. Command Interface configuration CoS-to-Traffic Class QoS map to an interface: switch(int Te 0/2)#qos cos-traffic-class test See - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 197
Sets the outbound CoS value for all packets with inbound CoS 7. Defaults There are no CoS-to-CoS mutation QoS maps defined. Command values go through unchanged: switch(config)#qos map cos-mutation test 0 1 2 3 5 4 6 7 switch(config)#interface tengigabitethernet 0/1 switch(conf-if-te-0/1)#qos - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 198
11 qos map cos-mutation See Also qos cos-mutation, show qos maps 180 Converged Enhanced Ethernet Command Reference 53-1001347-01 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 199
default CoS, and CoS-to-CoS mutation policies. Traffic Class is a reference to a scheduler queue and packet servicing default behavior recommended in IEEE 802.1Q for systems supporting eight switch(config)#qos map cos-traffic-class test 1 0 2 3 4 5 6 7 To delete a CoS-to-Traffic Class QoS map: switch - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 200
policy. All multicast Traffic Class packet expansion queues are serviced Deficit Weighted Round Robin (DWRR). Synopsis qos queue multicast 30 40 To return the system to the default multicast Traffic Class packet expansion scheduler policy: switch(config)#no qos queue multicast scheduler See Also - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 201
less than 6. The range of valid values is 0-100 percent. Sets the DWRR weight for Traffic Class 3 in units of bandwidth percentage left over after servicing all of the Strict Priority Traffic Classes. The sum of all weight values must equal 100 percent. The weight 0 value is only valid when the - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 202
no default value for each weight value. Command Global configuration mode Modes Description Use this command to configure the Traffic Class packet scheduler policy. Eight Traffic Classes are supported with a configurable number of them being Strict Priority and any remaining ones being serviced - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 203
. Guidelines Examples To lower the maximum multicast packet expansion rate to 10000pkt/s: switch(config)#qos rcv-queue multicast rate-limit 10000 To return the system to the default multicast packet expansion rate limit values: switch(config)#no qos rcv-queue multicast rate-limit See Also qos rcv - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 204
(pkt). The range of valid values is 0-2047 packets. .Defaults The default is 64 packets for each multicast Traffic Class. Command Global configuration mode Modes 1000 To return the system to the default multicast packet expansion Tail Drop Threshold value: switch(config)#no qos rcv-queue multicast - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 205
all incoming priority markings with the Interface Default CoS. The CoS mode sets the user priority based on the incoming CoS value, if the to the trust mode: switch(conf-if-te-0/1)#qos trust cos To return the interface QoS to the default value or to the untrusted state: switch(conf-if-te-0/1)#no qos - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 206
the output to report on only the named CEE map. Defaults The default behavior without the optional operand is to report on all defined command. Guidelines Examples To display information on all of the defined CEE maps: switch#show cee maps CEE Map test Precedence 1 Priority Group Table 0: Weight - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 207
, it disables PFC operationally. Examples To display all of the configured flow control information for a 10 Gbps Ethernet interface: switch#show qos flowcontrol interface tengigabitethernet 0/1 Interface TenGigabitEthernet 0/1 Mode PFC DCBX enabled for PFC negotiation TX 0 frames TX TX RX - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 208
Gbps Ethernet interface: switch#show qos interface tengigabitethernet 0/1 Interface TenGigabitEthernet 0/1 Provisioning mode cee CEE Map demo Default CoS 0 Interface (packets) TrafficClass: 0 1 2 3 Threshold: 64 64 64 64 190 Converged Enhanced Ethernet Command Reference 53-1001347-01 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 209
show qos interface 11 See Also Traffic Class Scheduler configured for 0 Strict Priority queues TrafficClass: 0 1 2 3 4 5 6 7 DWRRWeight: 0 0 0 0 60 0 40 0 Multicast Packet Expansion Traffic Class Scheduler TrafficClass: 0 1 2 3 DWRRWeight: 25 25 25 25 cee-map, priority table Converged Enhanced - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 210
only the named CoS-to-Traffic Class QoS maps. Defaults The default behavior without any specified operands is to report on no usage guidelines for this command. Guidelines Examples To display information on the defined QoS maps: switch#show qos maps CoS-to-CoS Mutation map 'test' In-CoS: 0 1 2 3 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 211
the runtime state retrieved from the interface reflecting the number of packets and bytes sent and received for each priority. Usage For a stand-alone switch, all ASICs are considered as slot number zero (0). Guidelines Examples To display the queueing information for a 10 Gbps Ethernet interface - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 212
Examples To display the runtime ingress queue state information retrieved from the dataplane for a 10 Gbps Ethernet interface: switch#show qos rcv-queue interface tengigabitethernet 0/2 Interface TenGigabitEthernet 0/2 In-use 404019 bytes, Total buffer 1081344 bytes 0 packets dropped - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 213
queueing statistics for all ASICs within the system. Defaults There are no default configurations for this command. Command EXEC mode Modes Description queue crossing the maximum queue depth. Usage For a stand-alone switch, all ASICs are considered as slot number zero (0). Guidelines Examples - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 214
11 show qos rcv-queue multicast 196 Converged Enhanced Ethernet Command Reference 53-1001347-01 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 215
are no defaults for this command. Command Global configuration mode Modes Description Use this command to clear all accumulated port authentication statistics on all ports. Usage There are no usage guidelines for this command. Guidelines Examples To clear dot1x statistics: switch(config)#clear - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 216
are no defaults for this command. Command Global configuration mode Modes Description Use this command to clear all of the dot1x statistics for a specific interface port. Usage There are no usage guidelines for this command. Guidelines Examples To clear dot1x statistics on a port: switch(config - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 217
Synopsis dot1x authentication no dot1x authentication Operands none Defaults There are no defaults for this command. Command Interface configuration mode Examples To enable dot1x on a port: switch(config)#interface tengigabitethernet 0/1 switch(conf-if-te-0/1)#dot1x authentication See Also none - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 218
. Synopsis dot1x enable no dot1x enable Operands none Defaults By default, authentication is disabled globally. Command Global configuration mode Guidelines Examples To enable 802.1X authentication globally: switch(config)#dot1x enable See Also none 200 Converged Enhanced Ethernet Command Reference - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 219
the no dot1x port-control command to return to the default setting. Usage There are no usage guidelines for this command. Guidelines Examples To enable the port state to auto: switch(config)#interface tengigabitethernet 0/1 switch(conf-if-te-0/1)#dot1x port-control auto See Also none Converged - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 220
to perform authentication after a failed authentication. Use the no dot1x quiet-period command to return to the default setting. When a switch cannot authenticate a client, the switch remains idle for a quiet-period interval of time, then attempts the operation again. Usage Changing the quiet - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 221
Operands name Specifies the name of the interface. Defaults There are no defaults for this command. Command Privileged EXEC mode Modes Examples To initiate reauthentication on interface tengigabitethernet 0/1: switch#dot1x reauthenticate interface tengigabitethernet 0/1 See Also none - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 222
no defaults for this command. Command Interface configuration mode Modes Description Use this command to enable reauthentication on a port. Usage There are no usage guidelines for this command. Guidelines Examples To enable reauthentication on a port: switch(config)#interface tengigabitethernet - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 223
the maximum number of reauthentication attempts to 5: switch(config)#interface tengigabitethernet 0/1 switch(conf-if-te-0/1)#dot1x reauthMax 5 To set the reauthentication maximum to the default value: switch(config)#interface tengigabitethernet 0/1 switch(conf-if-te-0/1)#no dot1x reauthMax See Also - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 224
attempts. The range of valid values is 1-65535. Defaults The default time is 3600 seconds. Command Interface configuration mode Modes the amount of time between reauthorization attempts: switch(config)#interface tengigabitethernet 0/1 switch(conf-if-te-0/1)#dot1x timeout re-authperiod 25 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 225
seconds Operands seconds Specifies the number of seconds that a switch waits for the transmission of packets by the switch to the authentication server. The range of valid values is 1-65535. Defaults The default timeout is 30 seconds. Command Interface configuration mode Modes Description - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 226
dot1x timeout supp-timeout seconds Operands seconds Specifies the number of seconds that the switch waits for a response to the EAP frame. The range of valid values is 1-65535. Defaults The default timeout is 30 seconds. Command Interface configuration mode Modes Description Use this command to - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 227
attempts. The range of valid values is 1-65535. Defaults The default timeout is 30 seconds. Command Interface configuration mode Modes frame from the client before retransmitting the request: switch(config)#interface tengigabitethernet 0/1 switch(config-if)#dot1x timeout tx-period 34 See Also - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 228
There are no defaults for this command. Command EXEC mode Modes Description Use this command to display the overall state of dot1x on the system. Usage There are no usage guidelines for this command. Guidelines Examples To display the state of the system: switch#show dot1x 802.1X Port-Based - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 229
all of the ports. Synopsis show dot1x all Operands none Defaults There are no defaults for this command. Command EXEC mode Modes Description Use this information for all of the ports: switch#show dot1x all 802.1X Port-Based Authentication Enabled PAE Capability: Authenticator Only - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 230
12 show dot1x all See Also none 212 Converged Enhanced Ethernet Command Reference 53-1001347-01 - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 231
interface name Operands name Specifies the name of the interface. Defaults There are no defaults for this command. Command EXEC mode Modes Description Use this command information for the authenticator associated with a port: switch#show dot1x diagnostics interface tengigabitethernet 0/1 802.1X - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 232
There are no defaults for this command. Command EXEC mode Modes Description Use this command to display the state of a specified interface. Usage There are no usage guidelines for this command. Guidelines Examples To display the state of 10 Gbps Ethernet interface 0/1: switch#show dot1x - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 233
Operands name Specifies the name of the interface. Defaults There are no defaults for this command. Command EXEC mode Modes Description Examples To display all statistical information of the established session: switch#show dot1x session-info interface tengigabitethernet 0/1 802.1X Session - HP StorageWorks 4/64 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 234
are no defaults for this command. Command EXEC mode Modes Description Use this command to display the statistics of a specified interface. Usage There are no usage guidelines for this command. Guidelines Examples To display the statistics for 10 Gbps Ethernet interface 0/1: switch#show dot1x
53-1001347-01
28 July 2009
Converged Enhanced
Ethernet Command
Reference
Supporting Fabric OS v6.3.0