HP StorageWorks 50 StorageWorks Modular Smart Array 50 Storage Enclosure User - Page 24

SAS cabling guidelines, Power cords, your maximum length may be up to 3.66 m 12 ft. - storageworks modular smart array 50

Get HP StorageWorks 50 - Modular Smart Array PDF manuals and user guides View all HP StorageWorks 50 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

24 HP StorageWorks Modular Smart Array 50 Storage Enclosure User Guide SAS cabling guidelines Observe the following guidelines: • Only use supported SAS cables with 3-GB connectors • Always be sure that the servers attached to the storage enclosure are powered down and power cords are disconnected before connecting SAS cables. Power cords The power cord should be approved for use in your country. The power cord must be rated for the product and for the voltage and current marked on the electrical ratings label of the product. The voltage and current rating for the cord should be greater than the voltage and current rating marked on the product. In addition, the diameter of the wire must be a minimum of 1.00 mm2 or 18 AWG, your maximum length may be up to 3.66 m (12 ft). WARNING: To reduce the risk of electric shock or damage to the equipment: • Do not disable the power cord grounding plug. The grounding plug is an important safety feature. • Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all times. • Unplug the power cord from the power supply to disconnect power to the equipment. • Do not route the power cord where it can be walked on or pinched by items placed against it. Pay particular attention to the plug, electrical outlet, and the point where the cord extends from the storage system. To connect AC power cords: 1. Connect the power cords to the power supplies. 2. Connect the power cords to the AC power source.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
24
HP StorageWorks Modular Smart Array 50 Storage Enclosure User Guide
SAS cabling guidelines
Observe the following guidelines:
•
Only use supported SAS cables with 3-GB connectors
•
Always be sure that the servers attached to the storage enclosure are powered
down and power cords are disconnected before connecting SAS cables.
Power cords
The power cord should be approved for use in your country. The power cord
must be rated for the product and for the voltage and current marked on the
electrical ratings label of the product. The voltage and current rating for the cord
should be greater than the voltage and current rating marked on the product. In
addition, the diameter of the wire must be a minimum of 1.00 mm
2
or 18 AWG,
your maximum length may be up to 3.66 m (12 ft).
WARNING:
To reduce the risk of electric shock or damage to
the equipment:
•
Do not disable the power cord grounding plug. The grounding
plug is an important safety feature.
•
Plug the power cord into a grounded (earthed) electrical outlet
that is easily accessible at all times.
•
Unplug the power cord from the power supply to disconnect
power to the equipment.
•
Do not route the power cord where it can be walked on or
pinched by items placed against it. Pay particular attention to
the plug, electrical outlet, and the point where the cord extends
from the storage system.
To connect AC power cords:
1.
Connect the power cords to the power supplies.
2.
Connect the power cords to the AC power source.