HP StorageWorks MSA 2/8 HP StorageWorks SAN Switch rack mount kit installation
HP StorageWorks MSA 2/8 - SAN Switch Manual
View all HP StorageWorks MSA 2/8 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP StorageWorks MSA 2/8 manual content summary:
- HP StorageWorks MSA 2/8 | HP StorageWorks SAN Switch rack mount kit installation - Page 1
switch models: • SAN Switch 2/8V • SAN Switch 2/8 • SAN Switch 2/8-EL • SAN Switch 2/16V • SAN Switch 2/16 • SAN Switch 2/16N • SAN Switch 2/32 • SAN Switch 4/32 • SAN Switch 4/32B • 4/8 SAN Switch • 4/16 SAN Switch • 4/64 SAN Switch • 8/8 SAN Switch • 8/24 SAN Switch • 8/40 SAN Switch • 8/80 SAN - HP StorageWorks MSA 2/8 | HP StorageWorks SAN Switch rack mount kit installation - Page 2
lock for use with the SAN Switch 2/32 only. 14 #8-32 x 5/16-inch Phillips panhead SEMS screws for use with the 4/8, 4/16, 4/32, 4/64 SAN and 4/32B SAN Switches, and the 2/16, 2/ 8V, 2/16V, MP Router, 400 MP Router, 8/8, 8/24, 8/40, 8/80, and FCoE Converged Network Switch NOTE: All devices require 10 - HP StorageWorks MSA 2/8 | HP StorageWorks SAN Switch rack mount kit installation - Page 3
2. Choose a mounting location for the device in the rack. Figure 1 Installing the rear mounting brackets (HP 10000 Series Rack) Figure 2 Installing the rear mounting brackets (HP System/e Rack) NOTE: The SAN Switch Rack Mount Kit contains rails labeled Left and Right to designate the left side and - HP StorageWorks MSA 2/8 | HP StorageWorks SAN Switch rack mount kit installation - Page 4
screws SAN Switch 2/16 SAN Switch 2/8V SAN Switch 2/16V Ten (five per rail) N/A SAN Switch 2/32 N/A Twelve (six per rail) 4/8 SAN Switch 4/16 SAN Switch SAN Switch 4/32 Ten (five per rail) N/A 4/32B SAN Switch Six (three per rail) N/A MP Router Six (three per rail) N/A 4/64 SAN Switch - HP StorageWorks MSA 2/8 | HP StorageWorks SAN Switch rack mount kit installation - Page 5
8 when attaching the inner rails to the SAN Switch 2/16V or SAN Switch 2/16N. Figure 6 Securing the inner rails to the MP Router Figure 7 Securing the inner rails to the 4/64 SAN Switch NOTE: For factory integration only, tighten the #8-32 x 5/16-inch Phillips panhead SEMS screws and torque - HP StorageWorks MSA 2/8 | HP StorageWorks SAN Switch rack mount kit installation - Page 6
plenum included in the switch accessory kit: • SAN Switch 2/8V • SAN Switch 2/16 • SAN Switch 2/16V • 4/8 SAN Switch • 4/16 SAN Switch • 4/32B SAN Switch • 8/8 SAN Switch • 8/24 SAN Switch See "Installing the plenum (if required)" on page 6 for installation instructions. If you are not installing
HP StorageWorks
SAN Switch rack mount kit
installation instructions
© Copyright 2004-2009 Hewlett-Packard Development Company,
L.P.
Ninth edition: September 2009
The information in this document is subject to change without notice.
Printed in the US
www.hp.com
A7511-90905
About this document
This document describes how to use the SAN Switch Rack Mount Kit
(part number A7511A) to rack mount SAN switches and routers.
Supported devices
Use the SAN Switch Rack Mount Kit to install the following switch models:
•
SAN Switch 2/8V
•
SAN Switch 2/8
•
SAN Switch 2/8-EL
•
SAN Switch 2/16V
•
SAN Switch 2/16
•
SAN Switch 2/16N
•
SAN Switch 2/32
•
SAN Switch 4/32
•
SAN Switch 4/32B
•
4/8 SAN Switch
•
4/16 SAN Switch
•
4/64 SAN Switch
•
8/8 SAN Switch
•
8/24 SAN Switch
•
8/40 SAN Switch
•
8/80 SAN Switch
•
1606 Extension SAN Switch
•
FCoE Converged Network Switch
•
Encryption SAN Switch
•
Multi-protocol (MP) Router
•
400 Multi-protocol (MP) Router
Supported HP custom racks
Use the SAN Switch Rack Mount Kit with the following HP StorageWorks
custom racks only:
•
HP 9000 Series Rack
•
HP 10000 Series Rack
•
HP 10000 G2 Series Rack
•
HP System/e Rack
NOTE:
In this document, “HP 10000 Series Rack” refers to both the HP
10000 Series Rack and the HP 10000 G2 Series Rack.
Related documentation
For the latest B-series switch product documentation, see the
storage
section on the following HP website:
h
t
tp://w
w
w
.hp
.co
m/su
ppo
r
t/man
uals
Page 1