HP StoreOnce 4210 HP StoreOnce Backup System Linux and UNIX Configuration guid - Page 16

HP-UX 11i v2/v3 (PA-RISC & IA64), Overview, Configuring the HP StoreOnce Backup System for iSCSI,

Get HP StoreOnce 4210 PDF manuals and user guides View all HP StoreOnce 4210 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

3 HP-UX 11i v2/v3 (PA-RISC & IA64) Overview This chapter describes how to configure the HP StoreOnce Backup System for use with the following HP-UX operating systems: • HP-UX 11i v2 (PA-RISC and IA64) • HP-UX 11i v3 (PA-RISC and IA64) NOTE: A block size no larger than 256 KB is strongly recommended when working with HP-UX 11i v2. See Using large block sizes with HP-UX 11i V2 (page 23). Configuring the HP StoreOnce Backup System for iSCSI If your product supports iSCSI use the information in this section to configure it. If your product does not support iSCSI, go to Configuring the HP Backup System for Fibre Channel (page 20). How to install the iSCSI software initiator The iSCSI Software Initiator is located at the HP Software Depot. 1. Go to http://www.software.hp.com. 2. Enter iSCSI Software Initiator in the search box. 3. When the search results show iSCSI Software Initiator, click on Receive for Free. 4. In the Software Specification window, highlight the HP-UX version on which you want to install the HP-UX iSCSI Software Initiatot.Then complete the required fields and click on Next >> 5. Look for Download Software, then click on the iSCSI Software Initiator version that you would like to download. 6. In the Document column (next to the Download Software column), click on Installation Instruction to download instructions for using the Software Distributor tool to install the iSCSI Software Initiator. NOTE: The Software Distributor is used for software installations on HP-UX systems. It also provides an interface for removing software from HP-UX systems. 7. After the system reboots, verify that the installation was successful by issuing the swlist command as follows: swlist iSCSI-00 If the HP-UX iSCSI Software Initiator is installed correctly, the output will be: HP-UX 11i v2 # Initializing... # Contacting target "localhost"... # # Target: localhost:/ # # iSCSI-00 B.11.23.03e HP-UX iSCSI Software Initiator iSCSI-00.ISCSI-SWD B.11.23.03e HP-UX iSCSI Software Initiator HP-UX 11i v3 # Initializing... # Contacting target "localhost"... # # Target: localhost:/ # 16 HP-UX 11i v2/v3 (PA-RISC & IA64)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
3HP-UX 11i v2/v3 (PA-RISC & IA64)
Overview
This chapter describes how to configure the HP StoreOnce Backup System for use with the following
HP-UX operating systems:
•
HP-UX 11i v2 (PA-RISC and IA64)
•
HP-UX 11i v3 (PA-RISC and IA64)
NOTE:
A block size no larger than 256 KB is strongly recommended when working with HP-UX
11i v2. See
Using large block sizes with HP-UX 11i V2 (page 23)
.
Configuring the HP StoreOnce Backup System for iSCSI
If your product supports iSCSI use the information in this section to configure it.
If your product does not support iSCSI, go to
Configuring the HP Backup System for Fibre
Channel (page 20)
.
How to install the iSCSI software initiator
The iSCSI Software Initiator is located at the HP Software Depot.
1.
Go to
h
t
tp://w
w
w
.s
o
f
t
w
ar
e
.hp
.co
m
.
2.
Enter
iSCSI Software Initiator
in the
search
box.
3.
When the search results show
iSCSI Software Initiator
, click on
Receive for Free
.
4.
In the
Software Specification
window, highlight the HP-UX version on which you want to install
the HP-UX iSCSI Software Initiatot.Then complete the required fields and click on
Next >>
5.
Look for
Download Software
, then click on the iSCSI Software Initiator version that you would
like to download.
6.
In the
Document
column (next to the
Download Software
column), click on
Installation Instruction
to download instructions for using the Software Distributor tool to install the iSCSI Software
Initiator.
NOTE:
The Software Distributor is used for software installations on HP-UX systems. It also
provides an interface for removing software from HP-UX systems.
7.
After the system reboots, verify that the installation was successful by issuing the
swlist
command as follows:
swlist iSCSI-00
If the HP-UX iSCSI Software Initiator is installed correctly, the output will be:
HP-UX 11i v2
# Initializing...
# Contacting target "localhost"...
#
# Target: localhost:/
#
# iSCSI-00 B.11.23.03e HP-UX iSCSI Software Initiator
iSCSI-00.ISCSI-SWD B.11.23.03e HP-UX iSCSI Software Initiator
HP-UX 11i v3
# Initializing...
# Contacting target "localhost"...
#
# Target: localhost:/
#
16
HP-UX 11i v2/v3 (PA-RISC & IA64)