HP StoreOnce D2D4324 HP StoreOnce 2620 Backup Start here poster (BB852-90901, - Page 1

BB852-90901 Balham Eng front.pdf 1 10/09/2012 15:50 HP StoreOnce 2620 iSCSI Backup Start here • The host is the network server that you wish to back up. • The HP StoreOnce Backup system should be connected to Gigabit Ethernet. 100 Base-T Ethernet will limit performance. • For more detailed information about installing, configuring and using the HP StoreOnce Backup system, see the Installation and Configuration Guide and the User Guide on the HP StoreOnce Backup CD-ROM. C M Y CM MY CY CMY K © 2012 Hewlett-Packard Development Company, L.P. Printed in Hungary www.hp.com 1 About your HP StoreOnce Backup system The HP StoreOnce Backup system is a disk-based storage appliance for backing up host network servers or PCs to target devices on the appliance. These devices are configured as NAS Share, Virtual Tape Library or Catalyst Store targets for backup applications. To find out which backup applications are compatible with HP StoreOnce functions go to www.hp.com/go/ebs. TIP: To find out more about configuring and using NAS target devices, iSCSI virtual tape libraries and Catalyst Stores, see the HP StoreOnce Backup system User Guide on the CD-ROM. 4 Connect the hardware There are two physical network ports on the rear of the unit, Port 1 and Port 2; this allows the HP StoreOnce Backup system to be connected to two separate networks and used to back up host devices on both networks. Alternatively, the two network ports may be bonded together to gain bandwidth and failover benefits when on a single network. Port 1 (the lower port) must always be connected. If you are connecting to one network only, you must use Port 1. Back Panel 2 IMPORTANT - Retrieve your license entitlement certificates (if purchased) Licensing is used to enable optional product functionality, such as Replication, Catalyst or other future features. If you have purchased any of these features, you should activate the license as soon as possible. Replication and Catalyst License Entitlement Certificates are supplied electronically when the product is purchased. The Entitlement Certificates are shipped in clearly marked card envelopes with your HP StoreOnce Backup system. These are valuable items so, to prevent them becoming lost, please ensure they are identified and put safely to one side during unpacking. Entitlement certificates for iLO2 Advance Packs and Smart Array Advance Packs are also supplied with the HP StoreOnce Backup system. It is strongly recommended that all licenses are redeemed as soon as possible. Go to the Webware site - webware.hp.com. For detailed information about activating licenses refer to the HP StoreOnce Installation and Configuration Guide on the StoreOnce CD. 1 Power socket 2 Video/monitor connector 3 USB keyboard connectors 4 Network port 1 - always used for data connection 5 iLO2 port - do not use for data connection 6 Beacon LED 7 RAID controller 8 (reserved for future use) 9 Network port 2 - used for data connection only if network configured for dual port IP addresses 1. Always use the supplied power cord to connect the HP StoreOnce Backup system to the mains power supply. For detailed safety information, see the Safety Guide on the CD-ROM. 2. Use any CAT-5E or CAT-6 network cables (also supplied with the product). To ensure that the HP StoreOnce Backup system is discovered successfully, install it on the same subnet as the host machines that will access it. Typical installations have the HP StoreOnce Backup system connected to the same Gigabit network switch as the host machines that are carrying out the backups in order to gain optimum performance. 3 Install the rack rails and unit(s) The supplied rail kits allow you to install the HP StoreOnce Backup system into square and round hole racks for 1U and 2U servers. If mounting the server into threaded hole or telco racks, please see www.racksolutions.com to purchase mounting hardware. Important Safety Information Use extreme caution when installing and pulling the unit out from the rack; it can slip and fall, causing damage to the HP StoreOnce Backup system or injury. HP is not responsible for any damage or injury caused by the mishandling of the HP StoreOnce Backup system. Always refer to the Safety Guide and the Installation and Configuration Guide on the HP StoreOnce Backup CD for detailed safety information. 1. Install the rails in the rack, as required. Follow the instructions provided separately with the rail kits. 2. Slide the HP StoreOnce Backup system into position in the rack and secure it to the rack rails using thumbscrews on the front bezel. NOTE: The label on the top of the HP StoreOnce Backup system contains useful identity information, such as the MAC address and default network name. Make a note of this information before you install the appliance in the rack. There is also a label with login information for the iLO2 management port. (There is also a pull-out strip in the front panel with the serial number and part ID.) Server Ethernet switch Supplied cable Server LAN Server HP StoreOnce Backup Connect the hardware continues overleaf BB852-90901