HP TouchSmart tm2-1019tx HP TouchSmart tm2 Notebook PC - Maintenance and Servi - Page 50

If it is necessary to remove the hard drive shield, remove the two Phillips PM3.0×3.0 hard drive

Get HP TouchSmart tm2-1019tx PDF manuals and user guides View all HP TouchSmart tm2-1019tx manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

3. Lift the rear edge of the hard drive cover, and then swing it up and forward. 4. Remove the hard drive cover. NOTE: The hard drive cover is included in the Plastics Kit, spare part number 592971-001. 5. Grasp the Mylar tab on the hard drive and slide the hard drive (1) to the left to disconnect it from the system board. 6. Remove the hard drive (2) from the hard drive bay. 7. If it is necessary to remove the hard drive shield, remove the two Phillips PM3.0×3.0 hard drive shield screws (1) from each side of the hard drive. 42 Chapter 4 Removal and replacement procedures ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
3.
Lift the rear edge of the hard drive cover, and then swing it up and forward.
4.
Remove the hard drive cover.
NOTE:
The hard drive cover is included in the Plastics Kit, spare part number 592971-001.
5.
Grasp the Mylar tab on the hard drive and slide the hard drive
(1)
to the left to disconnect it from
the system board.
6.
Remove the hard drive
(2)
from the hard drive bay.
7.
If it is necessary to remove the hard drive shield, remove the two Phillips PM3.0×3.0 hard drive
shield screws
(1)
from each side of the hard drive.
42
Chapter 4
Removal and replacement procedures
ENWW