HP Value Microportable Projector MP1400 Compaq MP1400 Microportable Projector - Page 19

Powering Off the Projector, Standby, IMPORTANT, CAUTION

Get HP Value Microportable Projector MP1400 PDF manuals and user guides View all HP Value Microportable Projector MP1400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

4. Power on your source (computer, PC Companion, or VCR, etc.) and launch the software application being used to display images on the projection screen. If applicable, press the Function key on the computer designated for external display. If there is a long delay between the time the startup screen displays and the time the presentation software is launched, the lamp may shut off and the projector will automatically go into standby mode. If this happens, press the Standby button 3 to power on the lamp.  When the startup screen disappears, the video from the attached computer displays. If there is no incoming video, the "Check Video Cable" message will display on the projection screen. Powering Off the Projector Follow these instructions to power off the projector. 1. Press the Standby button to turn off the projector lamp. The message "Going to Standby" displays, and the LED on the Standby button blinks amber. IMPORTANT: Allow the projector to cool down for about five minutes before turning it off. 2. Turn off the Main power switch on the back of the projector. 3. Disconnect the power cord from the electrical outlet and the projector. CAUTION: After the projector is turned off, wait at least one minute before turning the projector back on. Failure to follow this caution can result in damage to the projector.  1-12  MP1400 Microportable Projector

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
1-12
MP1400 Microportable Projector
4.
Power on your source (computer, PC Companion, or
VCR, etc.) and launch the software application
being used to display images on the projection
screen. If applicable, press the Function key on the
computer designated for external display.
If there is a long delay between the time the startup screen
displays and the time the presentation software is launched,
the lamp may shut off and the projector will automatically
go into standby mode. If this happens, press the
Standby
button
3
to power on the lamp.
When the startup screen disappears, the video from the
attached computer displays. If there is no incoming video, the
“Check Video Cable” message will display on the projection
screen.
Powering Off the Projector
Follow these instructions to power off the projector.
1. Press the
Standby
button to turn off the projector
lamp.
The message “Going to Standby” displays, and the LED on the
Standby
button blinks amber.
IMPORTANT:
Allow the projector to cool down for about five
minutes before turning it off.
2. Turn off the Main power switch on the back of the
projector.
3. Disconnect the power cord from the electrical outlet
and the projector.
CAUTION:
After the projector is turned off, wait at least one minute
before turning the projector back on. Failure to follow this caution
can result in damage to the projector.