HP Z23n User Guide - Page 18

Removing the monitor stand, Mounting the display head

Get HP Z23n PDF manuals and user guides View all HP Z23n manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Removing the monitor stand You can remove the display head from the stand to install the display head on a wall, a swing arm, or other mounting fixture. CAUTION: Before beginning to disassemble the monitor, be sure that the monitor is turned off and all cables are disconnected. 1. Disconnect and remove all cables from the monitor. 2. Lay the monitor face down on a flat surface covered by a clean, dry cloth. 3. Push up on the latch near the bottom center of the monitor (1). 4. Swing the bottom of the stand up until the mounting plate clears the recess in the panel (2). 5. Slide the stand out of the recess (3). Mounting the display head The display head can be attached to a wall, swing arm, or other mounting fixture. NOTE: This apparatus is intended to be supported by a UL or CSA Listed wall-mount bracket. If the monitor is TCO certified, the power cord plugged into the display head must be a shielded power cable. The use of a shielded power cable meets the TCO Certified criteria for display products. For information on TCO requirements, go to www.tcodevelopment.com. CAUTION: This monitor supports the VESA industry standard 100 mm mounting holes. To attach a thirdparty mounting solution to the display head, four 4 mm, 0.7 pitch, and 10 mm long screws are required. Longer screws must not be used because they may damage the display head. It is important to verify that the manufacturer's mounting solution is compliant with the VESA standard and is rated to support the weight of the display head. For best performance, it is important to use the power and video cables provided with the monitor. 1. Remove the display head from the stand. Removing the monitor stand on page 12. 12 Chapter 1 Getting Started

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
Removing the monitor stand
You can remove the display head from the stand to install the display head on a wall, a swing arm, or other
mounting fixture.
CAUTION:
Before beginning to disassemble the monitor, be sure that the monitor is turned off and all
cables are disconnected.
1.
Disconnect and remove all cables from the monitor.
2.
Lay the monitor face down on a flat surface covered by a clean, dry cloth.
3.
Push up on the latch near the bottom center of the monitor
(1)
.
4.
Swing the bottom of the stand up until the mounting plate clears the recess in the panel
(2)
.
5.
Slide the stand out of the recess
(3)
.
Mounting the display head
The display head can be attached to a wall, swing arm, or other mounting fixture.
NOTE:
This apparatus is intended to be supported by a UL or CSA Listed wall-mount bracket.
If the monitor is TCO certified, the power cord plugged into the display head must be a shielded power cable.
The use of a shielded power cable meets the TCO Certified criteria for display products. For information on
TCO requirements, go to
www.tcodevelopment.com
.
CAUTION:
This monitor supports the VESA industry standard 100 mm mounting holes. To attach a third-
party mounting solution to the display head, four 4 mm, 0.7 pitch, and 10 mm long screws are required.
Longer screws must not be used because they may damage the display head. It is important to verify that the
manufacturer’s mounting solution is compliant with the VESA standard and is rated to support the weight of
the display head. For best performance, it is important to use the power and video cables provided with the
monitor.
1.
Remove the display head from the stand.
Removing the monitor stand
on page
12
.
12
Chapter 1
Getting Started