HP Z240 Maintenance and Service Guide - Page 49

Chassis security, Smart Cover Sensor (optional), Setting the protection level

Get HP Z240 PDF manuals and user guides View all HP Z240 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

Chassis security Smart Cover Sensor (optional) The optional Smart Cover Sensor is a combination of hardware and software technology that alerts you when the side panel of the computer is removed (provided the sensor has been configured in Computer Setup (F10) Utility). Three levels of protection are available *: Level Setting Description Level 0 Disabled Sensor * is disabled (default). Level 1 Notify User When the computer restarts, a message indicates that the computer has been opened or the access panel has been removed. Level 2 Administrator Password When the computer restarts, a message indicates that the computer has been opened or the access panel has been removed. You must enter the administrator password to continue. * Smart Cover Sensor settings are changed using Computer Setup (F10) Utility. Setting the protection level To set the Smart Cover Sensor protection level: 1. Turn on or restart the computer. 2. During startup, press and hold the F10 key until you enter Computer Setup (F10) Utility. Press enter to bypass the title screen, if necessary. NOTE: If you do not press the F10 key at the appropriate time, you must restart the computer, and then press and hold the F10 key again to access Computer Setup (F10) Utility. If you are using a PS/2 keyboard, you might see a keyboard error message. Disregard it. 3. Select Security > Smart Cover > Cover Removal Sensor, and follow the on-screen instructions. 4. Before exiting, select Main > Save Changes and Exit. Side access panel solenoid lock The side access panel solenoid lock (available only on specific workstations) secures the side access panel to the chassis. The solenoid is controlled by a local or remote signal. To lock the solenoid, set a password for the solenoid lock in Computer Setup (F10) Utility. To unlock the solenoid, remove the solenoid lock password in Computer Setup (F10) Utility. The solenoid lock FailSafe Key (available from HP) is is a device for manually disabling the solenoid lock. You will need the FailSafe Key in case of a forgotten password, power loss, or computer malfunction. Cable lock (optional) To prevent theft, you can attach a keyed cable lock to the rear chassis panel. This cable lock attaches to the chassis and secures it to the work area. Fault notification and recovery Fault notification and recovery features combine innovative hardware and software technology to prevent the loss of critical data and minimize unplanned downtime. Desktop management 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
Chassis security
Smart Cover Sensor (optional)
The optional Smart Cover Sensor is a combination of hardware and software technology that alerts you when
the side panel of the computer is removed (provided the sensor has been configured in Computer Setup (F10)
Utility).
Three levels of protection are available *:
Level
Setting
Description
Level 0
Disabled
Sensor
*
is disabled (default).
Level 1
Notify User
When the computer restarts, a message indicates that the computer has been
opened or the access panel has been removed.
Level 2
Administrator Password
When the computer restarts, a message indicates that the computer has been
opened or the access panel has been removed. You must enter the administrator
password to continue.
*
Smart Cover Sensor settings are changed using Computer Setup (F10) Utility.
Setting the protection level
To set the Smart Cover Sensor protection level:
1.
Turn on or restart the computer.
2.
During startup, press and hold the
F10
key until you enter Computer Setup (F10) Utility. Press
enter
to
bypass the title screen, if necessary.
NOTE:
If you do not press the
F10
key at the appropriate time, you must restart the computer, and
then press and hold the
F10
key again to access Computer Setup (F10) Utility.
If you are using a PS/2 keyboard, you might see a keyboard error message. Disregard it.
3.
Select
Security
>
Smart Cover
>
Cover Removal Sensor
, and follow the on-screen instructions.
4.
Before exiting, select
Main
>
Save Changes and Exit
.
Side access panel solenoid lock
The side access panel solenoid lock (available only on specific workstations) secures the side access panel to
the chassis. The solenoid is controlled by a local or remote signal.
To lock the solenoid, set a password for the solenoid lock in Computer Setup (F10) Utility. To unlock the
solenoid, remove the solenoid lock password in Computer Setup (F10) Utility.
The solenoid lock FailSafe Key (available from HP) is is a device for manually disabling the solenoid lock. You
will need the FailSafe Key in case of a forgotten password, power loss, or computer malfunction.
Cable lock (optional)
To prevent theft, you can attach a keyed cable lock to the rear chassis panel. This cable lock attaches to the
chassis and secures it to the work area.
Fault notification and recovery
Fault notification and recovery features combine innovative hardware and software technology to prevent the
loss of critical data and minimize unplanned downtime.
Desktop management
39