HP Z6100ps HP Designjet Z6100 Printer Series - Setup Poster (42 inch)
HP Z6100ps - DesignJet Color Inkjet Printer Manual
UPC - 882780990135
View all HP Z6100ps manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Z6100ps manual content summary:
- HP Z6100ps | HP Designjet Z6100 Printer Series - Setup Poster (42 inch) - Page 1
HP Designjet Z6100 42-in Printer Assembly instructions ©2007 Hewlett-Packard Company. Inkjet Commercial Division Avenida Graells 501 08174 Sant Cugat del Vallès, Barcelona Spain All rights reserved. EN Please read these instructions carefully 1m 3.5ft 1m 3.5ft 3m 10ft The space required for - HP Z6100ps | HP Designjet Z6100 Printer Series - Setup Poster (42 inch) - Page 2
Remove the packaging Steps 1 to 4. This task requires 2 people. Time required is 5 minutes. 5' x2 Boxes required 1 Remove the 4 upper plastic handles from the sides of the box (two each side), and then carefully remove the two side lids vertically. x4 2 Carefully cut the straps around the - HP Z6100ps | HP Designjet Z6100 Printer Series - Setup Poster (42 inch) - Page 3
Locate the bag of screws and the screwdriver provided. Notice that the screwdriver is slightly magnetic. Because spare screws are supplied, some screws will remain unused after assembly of the printer. 9 Remove the left leg from the box, and then remove the two pieces inside the leg. 10 Lower the - HP Z6100ps | HP Designjet Z6100 Printer Series - Setup Poster (42 inch) - Page 4
15 Use two screws on the outside of the right leg to attach the right leg to the cross-brace. x2 16 Use four screws to attach the cross-bar to the legs. x4 17 Notice that there is anti-slip material around two of the wheels on the feet. DO NOT REMOVE this material yet. 18 Place a foot on the left - HP Z6100ps | HP Designjet Z6100 Printer Series - Setup Poster (42 inch) - Page 5
x1 25 Position the left and right leg covers on the front of the legs (1), and then clip the rear edge (2) into place. 2 Attach the printer engine to the stand Steps 26 to 38. This task requires 4 people. Time required is 15 minutes. 15' x4 Boxes required 26 Remove the eight - HP Z6100ps | HP Designjet Z6100 Printer Series - Setup Poster (42 inch) - Page 6
slip material touch the floor. x4 35 Remove the pallet before lifting the printer to its upright position. x2 36 Use the hand holds at the rear of the printer engine to carefully lift the printer to its upright position. HP recommends four people to complete this task. x4 Page 6 37 Remove the two - HP Z6100ps | HP Designjet Z6100 Printer Series - Setup Poster (42 inch) - Page 7
two screws.) x4 41 Attach the two plastic brackets to the top part of the printer legs. Insert the tab at the bottom of the bracket into the leg, and then 'click' the top of the bracket into place. 42 Remove the bin assembly from the box that contains the stand and the - HP Z6100ps | HP Designjet Z6100 Printer Series - Setup Poster (42 inch) - Page 8
covering from the printer window and the front panel screen. 50 Remove the Quick Reference Guide holder from the supplies box. Attach the Quick Reference Guide holder by angling the holder forward at the top (1), positioning the two hooks, and then 'clicking' the lower part (2) to the rear - HP Z6100ps | HP Designjet Z6100 Printer Series - Setup Poster (42 inch) - Page 9
Up and Down buttons to highlight the language you want, and then press the OK button. 1' 57 Wait until this message appears. The front panel guides you through the procedures for inserting the ink supplies. Page 9 58 Gently pull down on the blue handle and then slide out the ink cartridge drawer. - HP Z6100ps | HP Designjet Z6100 Printer Series - Setup Poster (42 inch) - Page 10
drawer locks into position. 62 The printer 'beeps' when the cartridge is correctly inserted. 63 Follow the same instructions to insert the other seven ink cartridges. 64 Wait until this message appears on the front panel. 2' 65 Pull open the maintenance cartridge door, which is located on the - HP Z6100ps | HP Designjet Z6100 Printer Series - Setup Poster (42 inch) - Page 11
until this message appears on the front panel (about 1 minute). 1' 68 Open the printer window, and then remove the packing foam from the top of the printhead carriage. 69 Remove the packing tape that is holding down the printhead carriage latch. 70 Pull up and release the blue latch on top of the - HP Z6100ps | HP Designjet Z6100 Printer Series - Setup Poster (42 inch) - Page 12
firmly reseat the printheads. If the problem persists, refer to the HP Start-Up Kit CD/DVD. 78 Close the carriage assembly cover. 79 Make sure that the blue latch is correctly engaged, and then lower the latch. 80 Close the printer window. 81 Wait until the Ready for paper message appears on - HP Z6100ps | HP Designjet Z6100 Printer Series - Setup Poster (42 inch) - Page 13
blue hub from the left end of the spindle. Keep the spindle horizontal. 84 Slide one the rolls of paper that came with your printer onto the spindle. Make sure that the paper is oriented as shown. 85 Make sure that the black hub on the right side of the spindle is fully - HP Z6100ps | HP Designjet Z6100 Printer Series - Setup Poster (42 inch) - Page 14
message appears on the front panel. 91 Open the printer window. 92 Lift the paper-load lever. 93 Pull out approximately 1m (3 feet) of paper to avoid back tension on the spindle, which can cause difficulties when loading the paper into the printer. 1 m (3 feet) 94 Insert the lead-edge of the - HP Z6100ps | HP Designjet Z6100 Printer Series - Setup Poster (42 inch) - Page 15
button. Page 15 105 The printer will automatically perform paper advance and printhead alignment. During this process the printer will advance the paper up to 3 m (~10 feet) before printing. Macintosh users must wait for the printhead alignment. Windows users can proceed with software installation - HP Z6100ps | HP Designjet Z6100 Printer Series - Setup Poster (42 inch) - Page 16
do not try to stop the paper advance; it is necessary to ensure successful printhead alignment. The alignment and calibration x1 The assembly of your printer is complete. The following pages describe how to configure your computer for successful printing. Mac OS page 17 Windows page 18 Page 16 - HP Z6100ps | HP Designjet Z6100 Printer Series - Setup Poster (42 inch) - Page 17
then look for the 'Mac OS X HP Designjet Installer' icon. 4. Double-click the appropriate icon to launch the installer, and then follow the onscreen instructions. Note: HP recommends that you use the Easy Install option. 5. When the software has been installed, the HP Printer Setup Assistant starts - HP Z6100ps | HP Designjet Z6100 Printer Series - Setup Poster (42 inch) - Page 18
is connected, select Wired Networking. • Verify that the network settings are correct for the printer that you selected. • Select your printer from the list. If you have more than one HP Designjet Z6100 printer connected to the network, use the IP address that you noted earlier to confirm that - HP Z6100ps | HP Designjet Z6100 Printer Series - Setup Poster (42 inch) - Page 19
numerous paper types available for your printer. To use HP Color Center, you must first install it. Follow the instructions in your product installation CD/DVD. To access HP Color Center in Windows, double-click the following icon, which is on your computer desktop. To access HP Color Center in Mac - HP Z6100ps | HP Designjet Z6100 Printer Series - Setup Poster (42 inch) - Page 20
©2007 Hewlett-Packard Company. Inkjet Commercial Division Avenida Graells 501 08174 Sant Cugat del Vallès, Barcelona Spain All rights reserved. Printed in Germany Imprimé en Allemagne Stampato in Germania www.hp.com
2
h
1m
3.5ft
1m
3.5ft
3m
10ft
©2007 Hewlett-Packard Company.
Inkjet Commercial Division
Avenida Graells 501
08174
Sant Cugat del Vallès,
Barcelona
Spain
All rights reserved.
Assembly instructions
Please read these instructions carefully
Time required for assembly of the
printer is approximately 132 minutes.
The space required for assembly is
3 m (10 feet) in front and
1 m (3.5 feet) at the sides and rear.
4 people are required to perform
certain tasks.
1. Printer engine.
2. Stand and bin.
3. Spare box.
Used to rotate the printer.
4. Supplies.
Used to rotate the printer.
EN
4
2
2
3
1
Page 1
These assembly instructions explain how to assemble the printer.
Notice that the icons used in this document are also located on the printer packaging.
The icons help you locate the parts needed at each stage of the assembly.
Because spare screws are supplied, some screws will remain unused after assembly of
the printer.
HP Designjet Z6100
42-in Printer
x8
x8