HP dx2200 HP Compaq dx2200 MT Service Reference Card, 1st Edition - Page 1

Service Reference Card HP Compaq dx2200 MT Series Business PC © 2006 Hewlett-Packard Development Company, L.P. The informa- tion contained herein is subject to change without notice. HP shall not be liable for technical or editorial errors or omissions contained herein. Intel, Pentium, Intel Inside, and the Intel logo are trademarks or registered trademarks of the Intel Corporation and its subsidiaries in the U. S. and other countries. Document Number 415608-001. 1st Edition April 2006. Key Specifications Processor Type: Intel Celeron D or Pentium 4 RAM Type: DDR PC2 5300, non-ECC Maximum RAM Supported: 2GB Expansion Bus: PCI 2.2 Graphics Adapter Integrated controller. PCI-e support. Hard drive interface: SATA 1.5 Gb/s I/O Interfaces: Serial (1), parallel (1), USB 2.0 (6), diskette drive (1) System Setup and Boot Basic system information regarding system information, setup, power management, hardware, and passwords is maintained in the Setup Utility held in the system ROM. The Setup Utility is accessed by pressing the F10 key when prompted (on screen) to do so during the boot sequence. If the screen prompt opportunity is missed, a restart will be necessary. Computer Setup Menu Heading System Information Standard CMOS Setup Advanced BIOS Features Option / Description Lists the following main system specifications: • Product Name • SKU number • Processor Type • Processor Speed • CPU ID/Patch ID • Cache Size • Memory Size • System ROM • Integrated MAC Address • UUID • System serial number • Asset tracking number • Asset tag number Date (mm/dd/yy) - Allows you to set system date. Time (hh:mm:ss) - Allows you to set system time. PATA Controller - Disables/enables PATA controller PATA Ch 0 Master/PATA Ch 0 Slave - Allows you to detect IDE HDD size in selected channel, set access mode on selected channel, view firmware version, and capacities, run SMART HDD status, and perform various SMART tests. SATA Controller - Disables/enables onboard SATA controller. SATA Ch 1 Master/SATA Ch 2 Master - Allows you to detect HDD size in selected channel, set extended drive on selected channel, set access mode on selected channel, view firmware version, and capacities, run SMART HDD status, and perform various SMART tests. Floppy Controller - Disables/enables floppy drive controller. Drive A - allows you to set floppy drive to None or 1.44, 3.5 in. Halt On - Allows you to set POST error behavior. POST Delay - Allows you to set a POST delay to 0, 5, 10, 15, or 30 seconds. Device Boot Disabling - Allows you to restrict a device from booting. F9 Boot Menu - Disables/enables F9 Boot Menu. Removable Device Boot Priority - Allows you to specify the order of attached removable devices in the boot sequence. Hard Disk Boot Sequence - Allows you to specify the order in which attached HDDs are booted. Optical Drive Boot Sequence - Allows you to specify the order in which attached ODDs are checked for a bootable operating system image. Network Boot Sequence - Allows you to specify the order in which network devices are checked for a bootable OS image. First, Second, Third, or Fourth Boot Device - Allows you to specify boot sequence or disable any of the three devices. Boot up Numlock Status - Allows you to turn the default feature on or off. Security Option - Allows you to set security to determine whether a password is needed for booting or when entering Computer Setup. APIC Mode - Disables/enables APIC. MPS Version Control for OS - Allows you to select 1.1 or 1.4 MPS table version. BIOS write Protection - Disables/enables ROM BIOS upgrading. Execute Disable Bit - Disables/enables Execute Disable Bit (XD) to prevent malicious buffer overflow attacks Enhanced Intel SpeedStep Technology - enables/disables processor SpeedStep technology. Hyper-Threading Technology - enables/disables processor HyperThreading technology. Computer Setup Menu (Continued) Heading Option / Description Advanced Chipset Features UMA Frame Buffer - Allows you to select the Unified Memory Architecture (UMA) frame buffer size to 32MB, 64MB, or Auto. Init Display First (VGA Setting) - Allows you to set primary display device to PCI slot, OnChip VGA, or PCI-e. SURROUNDVIEW - Disables/enables SURROUNDVIEW (available when a PCI-e video card is installed. Auto Detect PCI Clk (VGA Setting)- Disables/enables PCI clock auto detection. Integrated Onboard HD Audio - Disables/enables onboard HD audio. Peripherals On-Chip USB Controller - Disables/enables USB controller. USB Legacy Support - Disables/enables USB keyboard and mouse. Onboard Audio - Allows you to auto-detect or disable onboard audio. Onboard LAN - Disables/enables onboard LAN controller. Onboard LAN Boot ROM- Disables/enables Boot ROM onboard on the LAN chip. Onboard Serial Port 1 - Allows you to select one of these settings: Disabled, 3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4, or 2E8/IRQ3. Onboard Parallel Port - Allows you to select one of these settings: Disabled, 378/IRQ7, 278/IRQ5, or 3BC/IRQ7. Parallel Port Mode - Allows you to set parallel port mode to SPP, EPP, ECP, ECP+EPP, or Normal. ECP Mode use DMA - If parallel port mode set to SECP or ECP+EPP, allows you to set DMA channel for ECP mode to 1 or 3. Power Management Setup After AC Power Loss- Allows you to select system power loss behavior to Last state, On, or Off. ACPI Suspend Type - Allows you to select system power loss behavior. External Modem S5 Wake-up - Disables/enables wake-up modem from S5. RTC Alarm Resume - Disables/enables RTC alarm. Date (of Month) Alarm - If resume by Alarm is enabled, allows you to select the day of the month to resume RTC alarm. Resume Time (hh:mm:ss) Alarm - If enabled, allows you to select what time the RTC alarm will resume. PnP/PCI Configurations Reset Configuration Data - Disables/enables automatic reconfiguration. Resources Controlled By - Allows you to select whether resources are controlled manually or automatically. IRQ Resources for IRQ 3, 4, 5, 7, 9, 10, 11, 12, 14, and 15. Allows you to assign each system interrupt a type depending on the device type using the interrupt. Maximum Payload Size - Allows you to set TLP payload size for the PCI-e devices to 128, 256, 512, 1024, 2048, or 4096 bytes. PC Health System Fan Fail Check - Disables/enables system fan detection during Status POST. Smart Fan Function - Disables/enables smart fan functionality. Current CPU Temperature - View. Current System Temperature - View. Current CPU Fan Speed - View. Current System Fan Speed - View. Vcore - View. +12V - View. VCC5 - View. +3.3V - View. VBAT (V) - View. 3VSB (V) - View. Load Optimized Defaults Allows you to reset Computer Setup to factory defaults. Set Supervi- Allows you to set a password to control access to Computer Setup. sor Password Set User Password Allows you to set a password to control access to the Computer. (Supervisor password must already be set for this feature to enable,) Save & Exit Allows you to save current settings and exit Computer Setup. Setup Exit With- Allows you to exit Computer Setup without saving changes. out Saving