HP rp2400 Basic Cable Connections - hp rp2400 Series of Servers - Page 9

Connect External Small Computer System Interface (SCSI) Devices, Connect a System Console - hardware manual

Get HP rp2400 PDF manuals and user guides View all HP rp2400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

HP rp2400 Series of Servers - Basic Cable Connections Front Panel Controls and indicators The graphic shown below illustrates locations of the external connections to the server. Figure 1-3 External Connections to the Server 100-240V~, 600W 6.0-2.6A, 50-60Hz win Path: 0/2/0 urbo win Path: 0/4/0 urbo On/Off Switch GSP Reset TOC Console/ UPS Port wi n Path: 0/2/0 urbo wi n urbo Path: 0/4/ 0 100-240V~, 600W 6.0-2.6A, 50-60Hz A B Ultra 2 W ide SCSI Path: 0/0/1/ 0 GSP Reset TO C Narro w S ingle Ended SCSI Path: 0/0/2/ 0 10/100BASE- T 10BASE- T Path: 0/0/0/ 0 LAN Consol e Console/ UPS Por t Path: 0/6/2 Ultra2 Wide SCSI Path: 0/0/1/0 A B Path: 0/6/2 Narrow Single Ended SCSI Path: 0/0/2/0 10/100BASE-T Path: 0/0/0/0 10BASE-T LAN Console Path: 0/6/0 Path: 0/6/0 Pull-Out Tab ccrr008 Connect External Small Computer System Interface (SCSI) Devices Connect external SCSI devices to the single ended SCSI bus (labeled: Narrow Single-Ended SCSI Path: 0/0/2/0) on the system card or to the Ultra 2 SCSI bus (labeled: Ultra 2 SCSI Path: 0/0/1/0). Ensure that all devices on the SCSI bus have a unique address and the last device is terminated. Refer to the documentation accompanying each device to learn how to set addresses and where to place terminators. Connect a System Console NOTE For more information on console configuration, refer to the rp24xx Hardware Manual (search on rp2400) at http://docs.hp.com. • Using the ASCII Terminal as a System Console. If an ASCII terminal is to be used as a console/UPS port, make sure that the keyboard is connected and a power cable is available. • Using a Secure Web Console PCI card as a System Console. If the Secure Web Console PCI card is to be used as a system console, first configure the Guardian Service Processor (GSP). For more information on GSP configuration, refer to the rp24xx Hardware Manual (search on rp2400) at http://docs.hp.com. Then, connect an RJ45 LAN cable to the Secure Web Console PCI card installed in an I/O card slot on the back of the server. Chapter 1 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
HP rp2400 Series of Servers - Basic Cable Connections
Front Panel Controls and indicators
Chapter 1
9
The graphic shown below illustrates locations of the external connections to the server.
Figure 1-3
External Connections to the Server
Connect External Small Computer System Interface (SCSI) Devices
Connect external SCSI devices to the single ended SCSI bus (labeled:
Narrow Single-Ended SCSI Path:
0/0/2/0)
on the system card or to the Ultra 2 SCSI bus (labeled:
Ultra 2 SCSI Path: 0/0/1/0
).
Ensure that all devices on the SCSI bus have a unique address and the last device is terminated. Refer to the
documentation accompanying each device to learn how to set addresses and where to place terminators.
Connect a System Console
NOTE
For more information on console configuration, refer to the
rp24xx Hardware Manual
(search
on
rp2400
) at
.
•
Using the ASCII Terminal as a System Console
. If an ASCII terminal is to be used as a console/UPS
port, make sure that the keyboard is connected and a power cable is available.
•
Using a Secure Web Console PCI card as a System Console
. If the Secure Web Console PCI card is
to be used as a system console, first configure the Guardian Service Processor (GSP). For more
information on GSP configuration, refer to the
rp24xx Hardware Manual
(search on
rp2400
) at
.
Then, connect an RJ45 LAN cable to the Secure Web Console PCI card installed in an I/O card slot on the
back of the server.
A
B
100-240V~, 600W
6.0-2.6A, 50-60Hz
Ultra 2 W ide SCSI
Path:
0/0/1/ 0
Narro w S ingle Ended SCSI
Path:
0/0/2/0
A
B
GSP Reset
TO C
10/100BASE- T
Path:
0/0/0/0
10BASE- T
LAN Consol e
Console/
UPS Por t
Path:
0/2/0
Path:
0/4/0
Path:
0/6/2
Path:
0/6/0
win
urbo
win
urbo
ccrr008
100-240V~, 600W
win
Path: 0/2/0
win
Path: 0/4/0
6.0-2.6A, 50-60Hz
urbo
urbo
On/Off
Console/
Switch
GSP Reset
TOC
UPS Port
Path: 0/6/2
Path: 0/6/0
Ultra2 Wide SCSI
Narrow Single
Path: 0/0/1/0
Ended SCSI
Path: 0/0/2/0
10/100BASE-T
10BASE-T
Pull-Out
Path: 0/0/0/0
LAN Console
Tab