Hikvision DS-2CD2123G0-I User Manual - Page 131

Configuring Region Exiting Detection, Area Settings, Draw Area, Sensitivity, Clear

Get Hikvision DS-2CD2123G0-I PDF manuals and user guides View all Hikvision DS-2CD2123G0-I manuals
Add to My Manuals
Save this manual to your list of manuals

Page 131 highlights

Network Camera User Manual 4. Click Area Settings and click Draw Area button to start the area drawing. 5. Click on the live video to specify the four vertexes of the detection region, and right click to complete drawing. 6. Set the Max. Size and Min. Size for valid targets. Targets smaller or larger than the valid target size are not able to trigger detection. Max. Size: The maximum size of a valid target. Targets with larger sizes would not trigger detection. Min. Size: The minimum size of a valid target. Targets with smaller sizes would not trigger detection. 7. Click Stop Drawing when finish drawing. 8. Drag the slider to set the sensitivity value. Sensitivity: Range [1-100]. Sensitivity stands for the percentage of the body part of an acceptable target that enters the pre-defined region. Sensitivity = 100 - S1/ST*100 S1 stands for the target body part that enters the pre-defined region ST stands for the complete target body. Example: if you set the value as 60, the action can be counted as an region entrance action only when 40 percent body part enters the region. Note: The Sensitivity of the detection is supported by certain models. Refer to actual display for details. 9. Repeat the above steps to configure other regions. Up to 4 regions can be set. You can click the Clear button to clear all pre-defined regions. 10. Click Arming Schedule to set the arming schedule. 11. Click Linkage Method to select the linkage methods. 12. Click Save to save the settings. Configuring Region Exiting Detection Purpose: Region exiting detection function detects people, vehicle or other objects which exit 130

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
Network Camera User Manual
130
4.
Click
Area Settings
and click
Draw Area
button to start the area drawing.
5.
Click on the live video to specify the four vertexes of the detection region, and
right click to complete drawing.
6.
Set the Max. Size and Min. Size for valid targets. Targets smaller or larger than
the valid target size are not able to trigger detection.
Max. Size
: The maximum size of a valid target. Targets with larger sizes would
not trigger detection.
Min. Size
: The minimum size of a valid target. Targets with smaller sizes would
not trigger detection.
7.
Click
Stop Drawing
when finish drawing.
8.
Drag the slider to set the sensitivity value.
Sensitivity
: Range [1-100]. Sensitivity stands for the percentage of the body part
of an acceptable target that enters the pre-defined region.
Sensitivity = 100
–
S
1
/S
T
*100
S
1
stands for the target body part that enters the pre-defined region S
T
stands for
the complete target body.
Example: if you set the value as 60, the action can be counted as an region
entrance action only when 40 percent body part enters the region.
Note:
The
Sensitivity
of the detection is supported by certain models. Refer to
actual display for details.
9.
Repeat the above steps to configure other regions. Up to 4 regions can be set. You
can click the
Clear
button to clear all pre
-
defined regions.
10.
Click
Arming Schedule
to set the arming schedule.
11.
Click
Linkage Method
to select the linkage methods.
12.
Click
Save
to save the settings.
Configuring Region Exiting Detection
Purpose:
Region exiting detection function detects people, vehicle or other objects which exit