Hikvision DS-2CD2123G0-I Quick Start Guide - Page 5

Emergency, Time Synchronization, Installation

Get Hikvision DS-2CD2123G0-I PDF manuals and user guides View all Hikvision DS-2CD2123G0-I manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

Introduction may burn out. Do not expose the device to high electromagnetic radiation or dusty environments. For an indoor-only device, place it in a dry and well-ventilated environment. Do not aim the lens at the sun or any other bright light. Make sure the running environment meets the requirement of the device. The operating temperature shall be -30° to 60° C (-22° to 140° F) or -40° to 60° C (-40° to 140° F), and the operating humidity shall be 95% or less (non-condensing). Do not place the camera in extremely hot, cold, dusty, or damp locations, and do not expose it to high electromagnetic radiation. Emergency If smoke, odor, or noise arises from the device, immediately turn off the power, unplug the power cable, and contact the service center. Time Synchronization Set up camera time manually for the first time access if the local time is not synchronized with that of the network. Visit the camera via Web browser/client software and go to the time settings interface. Installation Make sure the device is firmly secured to any wall or ceiling mountings. Be sure that there is enough space to install the camera and accessories. Make sure that the device in the package is in good condition and all the assembly parts are included. Make sure that the wall is strong enough to withstand at least foour times the weight of the camera and the mount. The standard power supply is 12 VDC, please make sure your power supply matches with your camera. Make sure that the power has been disconnected before you wire, install, or disassemble the device. Make sure that no reflective surface is too close to the camera lens. The IR light from the camera may reflect back into the lens causing reflection. For a device with this sticker, this device is intended for installation in a restricted access location, access can only be gained by service persons or by users who have been instructed about the reasons for the restrictions applied to the location and about any precautions that shall be taken. QSG DS-2CDx1xxG0-xxx 052620NA 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
QSG DS-2CDx1xxG0-xxx 052620NA
5
Introduction
may burn out.
Do not expose the device to high electromagnetic radiation or dusty environments.
For an indoor-only device, place it in a dry and well-ventilated environment.
Do not aim the lens at the sun or any other bright light.
Make sure the running environment meets the requirement of the device. The operating temperature shall
be -30° to 60° C (-22° to 140° F) or -40° to 60° C (-40° to 140° F), and the operating humidity shall be 95% or
less (non-condensing).
Do not place the camera in extremely hot, cold, dusty, or damp locations, and do not expose it to high
electromagnetic radiation.
Emergency
If smoke, odor, or noise arises from the device, immediately turn off the power, unplug the power cable,
and contact the service center.
Time Synchronization
Set up camera time manually for the first time access if the local time is not synchronized with that of the
network. Visit the camera via Web browser/client software and go to the time settings interface.
Installation
Make sure the device is firmly secured to any wall or ceiling mountings.
Be sure that there is enough space to install the camera and accessories.
Make sure that the device in the package is in good condition and all the assembly parts are included.
Make sure that the wall is strong enough to withstand at least foour times the weight of the camera and
the mount.
The standard power supply is 12 VDC, please make sure your power supply matches with your camera.
Make sure that the power has been disconnected before you wire, install, or disassemble the device.
Make sure that no reflective surface is too close to the camera lens. The IR light from the camera may
reflect back into the lens causing reflection.
For a device with this sticker, this device is intended for installation in a restricted
access location, access can only be gained by service persons or by users who have
been instructed about the reasons for the restrictions applied to the location and
about any precautions that shall be taken.