Hisense AP10CR1W Quick Start Guide - Page 1
Hisense AP10CR1W Manual
View all Hisense AP10CR1W manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
Portable Air Conditioner Electrical Shock Hazard • Plug into a grounded 3 prong outlet. • Do not remove ground prong. • Do not use an adapter. • Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. Keep unit upright at least 2 hours prior to use. Parts Package Before beginning, check that all parts are included in the parts package. non-adhesive foam seal adhesive foam seal (2) adhesive foam seal (2) coupling flexible exhaust hose window exhaust adapter window-lock bracket(2) outer slider section with vent inner slider section-short inner slider section outer slider section Drain hose clip (Heat pump models) 18'' to 50'' step 1 Suitable Windows The window installation kit allows you to install the air conditioner in most vertical-sliding windows 18'' to 50'' wide,or horizontal-sliding windows from 18'' to 50'' high. Choose the right panel Panel window A 18" B 9" 18" √ 19"-26" √ √ 27"-34" √ 35"-50" √ C 17" √ √ 18'' to 50'' D 17" panel A (18") √ panel C (17") panel B (9") panel D (17") step 2 Install Window Cut the adhesive foam seal to the proper length, and attach it to the window sash and frame. use shorter ones adhesive foam seal use longer ones Insert the vent panel assembly, including extension panels, if needed, into the window opening. Extend the extension panels, if used. rivets (2) Drain hose (Heat pump models) wood screws(4) Tools needed Phillips screwdriver Pencil Scissors vent panel extension panel If your window length requires more than 2 panels, after adjust the length, please secure the panels with rivets. rivet Cut the Non-adhesive foam seal to the window width. Stuff the foam seal between the glass and the window to prevent air and insects from getting into the room. Install the Window-lock bracket with wood screws as shown, if you need. window-lock bracket Non-adhesive foam seal wood screw step 3 Connect it together Install Exhaust Hose and Adapter Attach the coupling to the flexible exhaust hose. Turn counter-clockwise until securely locked into place. Attach the window exhaust adapter to the flexible exhaust hose. Turn counter-clockwise until securely locked into place. coupling window exhaust adapter flexible exhaust hose Connect The Hose To The Air Conditioner Insert the coupling into the slot on the back of the air conditioner. Slide down to lock the hose into place. coupling Turn The Unit On Turn the air conditioner on, and set the desired mode and temperature. outer slider section window exhaust adapter Plug In the Unit Be sure to use a grounded 3 prong outlet. Do not use an extension cord. Plug in the unit. 23 64¹⁄₈" To ensure proper ventilation Connect The Hose To The Window Roll the air conditioner to selected location. Attach the window exhaust adapter to the outer slider section (the piece with the large exhaust hole). Draining the Air Conditioner (Heat Pump models only) 1. Uncover the primary drain port. 2. Attach the drain hose to the primary drain hose. Make sure the connector does not have a water leak. 3. Place the other end of drain hose into a drain. Check to see that the hose lies flat and is in the drain. Make sure the hose end that goes to the drain is on a lower level than the hose end that connects to the unit. The hose should not be kinked or pinched. A. Primary drain hole B. Primary drain port C. Drain hose C B See the user manual for detailed instruction on installation and using the features and settings of the air conditioner and remote control. For questions about features, operation/performance, parts or service, Call: 1-877-465-3566 Monday to Friday: 9:00 a.m . - 6:00 p.m. (EST) or Visit: www.hisense-usa.com A The figures in this manual are based on the external view of a standard model. They may differ from that of the air conditioner you have selected.