Hitachi 42HDT20 Owners Guide - Page 26

How To Use The Remote, To Control Your Plasma Tv

Get Hitachi 42HDT20 PDF manuals and user guides View all Hitachi 42HDT20 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

STB POWER TV CBL VCR SOURCE WIZARDTAPE CD 2 AMP 3 6 DVD 1 5 9 INFO 4 8 MODE 7 0 ASPECT A/V NET SLEEP EXIT CH SELECT ANT TV/RGB MENU LAST CH GUIDE/TV SCHD VID 4 VID 5 VOL MUTE SVCS VCR PLUS+ VID 2 VID 1 PIP FREEZE VID 3 PIP CH PIP ACCESS VIDEO SWAP PIP MODE REC CLU-5723TSI HOW TO USE THE REMOTE TO CONTROL YOUR PLASMA TV ቨ CD, TAPE, AMP buttons When pressed, each of these buttons will blink to indicate the remote is in Audio mode. (see page 38) ቩ CHANNEL selector buttons CHANNEL selector buttons are used to select channels, lock access code, etc. Enter one, two, or three numbers to select channels. Enter "0" first for channels 1 to 9, or simply press the single digit channel you wish to tune then wait a few seconds for the TV to tune. For channels 100 and above, press the "1" button, wait until two dashes appear next to the channel display on your TV, then enter the remaining two numbers using the number buttons. Channel selection may also be performed by pressing CH up (̆) or down (̄). NOTE: The Plasma TV may not receive some channels if you are not in the correct ANTENNA/CABLE mode. (see page 58) ቪ SLEEP button Press this button to display the sleep timer in the lower left corner of the screen. Every subsequent press of this button will add 15 minutes to this timer, up to a maximum of three hours. Once set, use INFO when you want to view time remaining. If the SLEEP button is pressed while the timer is set, it will reset to the original condition. ቫ INFO button Press this button when you want to check the channel being received, the picture source, if the channel has stereo (ST) or second audio program (SAP), the time, CHANNEL ID and if the SLEEP timer is set. Signal Format Audio Selected Received Broadcast Rating Main Picture Source Audio Broadcast Wide Mode Picture Closed Mode Captioning Off Timer TV Time Out Sleep Timer Stereo (480i) ST/SA 16:9 Standard TV-PG DLSV Ant A 15 PIP TV-PG DLSV ABCDEFG 10:10 AM PIP Ant A 46-1234 Movies C.C. On Off 10:05 AM Time Lock 10:05 AM Sleep 0:01 Channel ID/Video ID Time PIP/Sub-Picture Source PIP/Sub-Picture S - IN: 3 When an S-VIDEO Input is connected to VIDEO: 3. YPBPR:1 When a COMPONENT VIDEO: Y-PBPR Input is connected to VIDEO: 1. ቭ ANTENNA button The ANT button will select between Antenna A and Antenna B each time the button is pressed. Ant A 10 ANT Ant B 28 ቮ TV/RGB button Press this button to toggle between RGB1, RGB2 and TV mode. 26

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
26
HOW TO USE THE REMOTE
TO CONTROL YOUR PLASMA TV
·
CD, TAPE, AMP buttons
When pressed, each of these buttons will blink to indicate the remote is in Audio mode. (see page 38)
¹
CHANNEL selector buttons
CHANNEL selector buttons are used to select channels, lock access code, etc.
Enter one, two, or three numbers to select channels.
Enter “0” first for channels 1 to 9, or simply press the single digit channel you
wish to tune then wait a few seconds for the TV to tune.
For channels 100 and above, press the “1” button, wait until two dashes
appear next to the channel display on your TV, then enter the remaining two numbers using the number buttons.
Channel selection may also be performed by pressing CH up (
±
) or down (
²
).
º
SLEEP button
Press this button to display the sleep timer in the lower left corner of the screen.
Every subsequent press of this button will add 15
minutes to this timer, up to a maximum of three hours.
Once set, use INFO when you want to view time remaining.
If the SLEEP
button is pressed while the timer is set, it will reset to the original condition.
»
INFO button
Press this button when you want to check the channel being received, the picture source, if the channel has stereo (ST) or second
audio program (SAP), the time, CHANNEL ID and if the SLEEP timer is set.
¼
ANTENNA button
The ANT button will select between Antenna A and Antenna B each time the button is pressed.
NOTE:
The Plasma TV may not receive some channels if you are not in the correct ANTENNA/CABLE mode.
(see page 58)
Ant B
28
Ant A
10
ANT
Ä
TV/RGB button
Press this button to toggle between RGB1, RGB2 and TV mode.
When an S-VIDEO
Input is connected to
VIDEO: 3.
When a COMPONENT
VIDEO: Y-P
B
P
R
Input
is connected to
VIDEO: 1.
S - IN: 3
Stereo (480i)
ST/SA
Audio
Broadcast
Audio Selected
Main Picture Source
Channel ID/Video ID
Time
PIP/Sub-Picture
Source
Signal Format
Received
TV-PG DLSV
PIP TV-PG DLSV
Broadcast
Rating
16:9 Standard
Movies
C.C. On
Off 10:05 AM
Time Lock 10:05 AM
Sleep 0:01
Wide
Mode
Picture
Mode
Closed
Captioning
Off Timer
TV Time Out
Sleep Timer
Ant A 15
ABCDEFG
10:10 AM
PIP Ant A 46-1234
PIP/Sub-Picture
YP
B
P
R
:1