Hitachi 50V720 Owners Guide - Page 58

Screw, Lamp Cover, Phillip Head, Screw Driver, Handle, Remove Screws, Lamp Unit, Tighten The Screws - lamp by phillips

Get Hitachi 50V720 - 50inch Rear Projection TV PDF manuals and user guides View all Hitachi 50V720 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

Lamp Replacement 3. Remove the screw securing the lamp cover with a Phillips head screw driver as shown. Remove the lamp cover. SCREW LAMP COVER PHILLIP HEAD SCREW DRIVER CAUTION: The lamp is very hot and may cause fire or severe burns. Wait at least 30~45 minutes to allow the lamp to cool before proceeding with lamp removal. 4. Remove the two screws that hold the lamp in place. Remove the lamp unit by holding the lamp handle, then pulling outwards. Exercise caution when removing the lamp unit to avoid injury to your fingers. NOTE: Do not put your hand in the Lamp Storage area after the Lamp Unit is removed, your may get burned. HANDLE LAMP UNIT Lamp Replacement REMOVE SCREWS HANDLE 5. Replace with the new lamp. Place the removed lamp into the empty box of the replacement lamp. Do not touch the front glass of the new lamp or its receptacle. This may shorten the life of the lamp and reduce the picture quality. • Push the lamp unit back to its original position. • Tighten the screws firmly on the lamp unit. If they are loose, the TV may not operate correctly. LAMP UNIT HANDLE HANDLE 58 TIGHTEN THE SCREWS

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
58
Lamp Replacement
3.
Remove the screw securing the lamp cover with a Phillips head screw driver as shown.
Remove the lamp
cover.
CAUTION:
The lamp is very hot and may cause fire or severe burns.
Wait at least 30~45 minutes to allow the
lamp to cool before proceeding with lamp removal.
4.
Remove the two screws that hold the lamp in place.
Remove the lamp unit by holding the lamp handle, then
pulling outwards.
Exercise caution when removing the lamp unit to avoid injury to your fingers.
NOTE:
Do not put your hand in the Lamp Storage area after the Lamp Unit is removed, your may get burned.
5.
Replace with the new lamp.
Place the removed lamp into the empty box of the replacement lamp.
Do not touch the front glass of the new
lamp or its receptacle.
This may shorten the life of the lamp and reduce the picture quality.
•
Push the lamp unit back to its original position.
•
Tighten the screws firmly on the lamp unit.
If they are loose, the TV may not operate correctly.
Lamp Replacement
SCREW
LAMP COVER
PHILLIP HEAD
SCREW DRIVER
HANDLE
REMOVE SCREWS
HANDLE
LAMP UNIT
HANDLE
LAMP UNIT
TIGHTEN THE SCREWS
HANDLE