Hitachi 55HDX99 Owners Guide - Page 11

Front/Side Panel Controls - no picture

Get Hitachi 55HDX99 PDF manuals and user guides View all Hitachi 55HDX99 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

First time use Front/Side Panel Controls ቩ POWER light indicator To turn the TV ON, press the main power switch located on the lower right side of the TV. A red stand-by indicator lamp located on the lower right corner of the front bezel will illuminate. The Plasma TV is now ready for remote ON/OFF operation. Lamp 1 Lamp 2 Indicating Lamp Power Status Lamp 1 Lamp 2 Off Off OFF. Operating When the main power switch is set to Off. Lights Red Off Off Blinking Blue OFF. (Stand-by) OFF. (Turning ON ) Off Lights Blue O n Lights Orange Off Off (Power Saving) When the main power switch on the TV is ON. TV MAIN POWER is ON ; but no picture is shown. TV MAIN POWER is ON ; picture is shown. TV MAIN POWER is ON with no signal input except antenna (no sync. signal). ቪ REMOTE CONTROL sensor Point your remote at this area when selecting channels, adjusting volume, etc. ቪ LEARNING AV NET sensor Point your equipment's remote control at this area while using the AV NET Learning Wizard. ቭ PHOTO INPUT Insert USB cable from your Digital Camera, USB memory or memory card USB drive to view your digital still pictures (see Owners Guide). ቫ SIDE INPUT JACKS (for IN PUT: 5) INPUT 5 provide Y-PBPR jacks for connecting equipment with this capability, such as a DVD player or Set Top Box. You may use composite video signal for this input. NOTE: 1. Your component outputs may be labeled Y, B-Y, and R-Y. In this case, connect the components B-Y output to the TV's PB input and the components R-Y output to the TV's PR input. 2. Your component outputs may be labeled Y-CBCR. In this case, connect the component CB output to the TV's PB input and the component CR output to the TV's PR input. 3. It may be necessary to adjust TINT to obtain optimum picture quality when using the Y-PBPR inputs (see page 47). 4. INPUT 3, INPUT 4 and INPUT 5 (Y/VIDEO) can be used for composite video and component video input. NOTES: 1. Your HITACHI Plasma TV will appear to be turned OFF (lights orange) if there is no video input when INPUT : 1, 2, 3, 4 and 5. Check the Power Light to make sure the TV is turned off or in Stand-by mode (lights red) when not in use. 2. Remote Control can not turn ON/OFF the "MAIN POWER" of the TV. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
11
First time use
¼
REMOTE CONTROL sensor
Point your remote at this area when selecting
channels, adjusting volume, etc.
¼
LEARNING AV NET sensor
Point your equipment’s remote control at this area
while using the AV NET Learning Wizard.
À
SIDE INPUT JACKS (for
IN PUT
: 5)
INPUT 5 provide Y-PBPR jacks for
connecting equipment with this capability, such as
a DVD player or Set Top Box. You may use
composite video signal for
this
input.
Front/Side Panel Controls
½
POWER light indicator
To turn the TV ON, press the main power
switch located on the lower right side of the
TV.
A red stand-by indicator lamp located on
the lower right corner of the front bezel will
illuminate.
The Plasma TV is now ready for
remote ON/OFF operation.
Indicating Lamp
Power Status
Operating
When the main power switch is set to Off.
OFF.
When the main power switch on the TV
(Stand-by)
is ON.
Blinking
Blue
n
O
TV
MAIN POWER is ON with no signal input
(Power Saving)
except antenna
(no sync. signal).
Lamp 1
Lamp 2
Lamp 1
Lamp 2
Off
Off
Lights
Red
Off
OFF.
Lights
Blue
Off
Off
(Turning ON )
OFF.
TV MAIN POWER is ON ; but no picture is shown.
TV MAIN POWER is ON ; picture is shown.
Lights
Orange
Off
Off
NOTES:
1.
Your HITACHI Plasma TV will appear to be turned OFF (lights orange) if there is no video input
when INPUT : 1, 2, 3, 4 and 5.
Check the Power Light to make sure the TV is turned off or
in Stand-by mode (lights red) when not in use.
2.
Remote Control can not turn ON/OFF the “MAIN
POWER” of the TV.
Your component outputs may be labeled
Y, B-Y, and R-Y. In this case, connect the
components B-Y output to the TV’s P
B
input and the components R-Y output to
the TV’s P
R
input.
Your component outputs may be labeled
Y-C
B
C
R
. In this case, connect the component
C
B
output to the TV’s P
B
input and the
component C
R
output to the TV’s P
R
input.
It may be necessary to adjust
TINT
to
obtain optimum picture quality when using
the Y-P
B
P
R
inputs (see page
4
7
).
INPUT 3
,
INPUT 4
and INPUT 5
(Y/VIDEO) can
be
used for composite video and component
video input.
NOTE:
1.
2.
3.
4.
Å
PHOTO INPUT
Insert USB cable from your Digital Camera, USB
memory or memory card USB drive to view your
digital still pictures (see Owners Guide).