Hitachi 60SX3B Owners Guide - Page 35

LEARNABLE BUTTONS, EXCLUSIVE BUTTONS, Storing Operation

Get Hitachi 60SX3B PDF manuals and user guides View all Hitachi 60SX3B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

THE GENIUS REMOTE TO LEARN ADDITIONAL USING THE GENIUS REMOTE TO LEARN ADDITIONAL FUNCTIONS - 35 -USING • The Genius Remote is equipped with a learning function which allows it to learn additional infrared control codes. This remote will not only control the television, a VCR, and a cable box, but also other electronic equipment which uses an infrared remote transmitter, by learning the transmitter's codes. • Only infrared remote control codes can be stored in memory. Before starting the memory operation • Since the infrared signals sent from the remote transmitter may be reflected by a wall, door, etc., even if the transmitter is not pointed directly at the device, it may operate. When storing the remote control codes of another device, turn OFF the power of the device (VCR, Cable Converter, etc.) If you do not do this, the device may work unexpectedly. The power could be turned ON, an important tape could be erased, the volume could increase too much, etc.. CLU-850GR Illustration LEARNABLE BUTTONS These buttons can "learn" the codes of other remote control transmitters when the MULTI-PAGE select switch is set to the "USER" mode. • MULTI-PAGE keys (A through L): No codes have been factory stored to these keys. • Learning buttons other than MULTI-PAGE buttons: the codes for the TV have been stored in memory. However, the remote control codes of other equipment (VTR, cable converter, audio equipment, etc.) can be stored using the learning function as shown on page 40 and later. EXCLUSIVE BUTTONS These buttons are for operating the TV. Storing Operation 1. Set the remote transmitter as shown below. Put the remote transmitter which contains the codes to be stored and the GENIUS REMOTE transmitter to face each other. (Distance should be 2 - 4 inches.)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
- 35 -USING
THE GENIUS REMOTE TO LEARN ADDITIONAL
USING THE GENIUS REMOTE TO LEARN ADDITIONAL
FUNCTIONS
• The Genius Remote is equipped with a learning function which allows it to learn
additional infrared control codes. This remote will not only control the television, a VCR,
and a cable box, but also other electronic equipment which uses an infrared remote
transmitter, by learning the transmitter's codes.
• Only infrared remote control codes can be stored in memory.
Before starting the memory operation
• Since the infrared signals sent from the remote transmitter may be reflected by a wall,
door, etc., even if the transmitter is not pointed directly at the device, it may operate.
When storing the remote control codes of another device, turn OFF the power of the
device (VCR, Cable Converter, etc.)
If you do not do this, the device may work unexpectedly. The power could be turned
ON, an important tape could be erased, the volume could increase too much, etc..
CLU-850GR Illustration
LEARNABLE BUTTONS
These buttons can "learn" the codes of other remote control transmitters when the
MULTI-PAGE select switch is set to the "USER" mode.
• MULTI-PAGE keys (A through L): No codes have been factory stored to these keys.
• Learning buttons other than MULTI-PAGE buttons: the codes for the TV have been
stored in memory. However, the remote control codes of other equipment (VTR, cable
converter, audio equipment, etc.) can be stored using the learning function as shown on
page 40 and later.
EXCLUSIVE BUTTONS
These buttons are for operating the TV.
Storing Operation
1. Set the remote transmitter as shown below.
Put the remote transmitter which contains the codes to be stored and the GENIUS
REMOTE transmitter to face each other. (Distance should be 2 - 4 inches.)