Hitachi 61SDX01B Owners Guide - Page 47

Using The Remote To Control Additional, Audio/video Equipment

Get Hitachi 61SDX01B PDF manuals and user guides View all Hitachi 61SDX01B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

USING THE REMOTE TO CONTROL ADDITIONAL precoded into the remote. 2. In the unlikely event that your DVD player cannot be operated after performing the above procedures, please consult your DVD player operating guide. 3. The remote control will remember the codes you have programmed in until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure stated above. (1) DVD Button This button allows the remote to control your DVD player by setting it to DVD mode. (2) PRECODED DVD Buttons These buttons transmit the chosen precoded DVD codes. (3) EXCLUSIVE TV Buttons These buttons are for operating the TV. MY DVD PLAYER CODE IS NOTE: Refer to instruction manual of the DVD player for operation of the buttons exclusively for the DVD player. USING THE REMOTE TO CONTROL ADDITIONAL AUDIO/VIDEO EQUIPMENT Operating the precoded function for your Audio/Video component. This remote is designed to operate different types of Audio/Video component. You must first program the remote to match the remote system of your Audio/Video component. (refer to page 37.) 1. Turn ON your Audio/Video component you wish to control with the Remote. 2. Aim the remote control at the front of your Audio/Video component. 3. Press and release the AV1, AV2 or AV3 button to switch to Audio/Video component pre-coded mode. 4. Hold down the AV1, AV2 or AV3 button on the remote and enter the two digit preset code that matches your Audio/Video component, as shown on page 37. The indicator light will flash 3 times if the code was accepted. 5. Aim the remote at the Audio/Video component and press the POWER button. The remote will turn off your Audio/Video component when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your Audio/Video component. If the Audio/Video component does not turn off, try a different two digit preset code. 6. The remote will now control your Audio/Video component. 7. Repeat steps 1 - 6 it you wish to program the remote to control another Audio/Video component. Be sure to use a different A/V button on the remote, since only one component can be programmed per button. 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
USING THE REMOTE TO CONTROL ADDITIONAL
47
precoded into the remote.
2. In the unlikely event that your DVD player
cannot be operated after performing the above procedures, please consult your
DVD player
operating guide.
3. The remote control will remember the codes you have programmed in until the batteries are removed from the remote
control. After replacing the batteries repeat the entire programming procedure stated above.
(1) DVD Button
This button allows the remote to control your DVD player
by setting it to DVD mode.
(2) PRECODED DVD Buttons
These buttons transmit the chosen precoded DVD codes.
(3) EXCLUSIVE TV Buttons
These buttons are for operating the TV.
MY DVD PLAYER CODE
IS:___________________
NOTE:
Refer to instruction manual of the DVD player
for operation of the buttons exclusively for the DVD player.
USING THE REMOTE TO CONTROL ADDITIONAL
AUDIO/VIDEO EQUIPMENT
Operating the precoded function for your Audio/Video component.
This remote is designed to operate different types of Audio/Video component. You must first program the remote to match the
remote system of your Audio/Video component.
(refer to page 37.)
1. Turn ON your Audio/Video component you wish to control with the Remote.
2. Aim the remote control at the front of your Audio/Video component.
3. Press and release the AV1, AV2 or AV3
button
to switch to Audio/Video component pre-coded mode.
4. Hold down the AV1, AV2 or AV3 button on the remote and enter the two digit preset code that matches your Audio/Video
component, as shown on page 37.
The indicator light will flash 3 times if the code was accepted.
5. Aim the remote at the Audio/Video component and press the POWER button.
The remote will turn off your Audio/Video
component when the correct two digit preset code is entered.
When this occurs, the remote control is programmed for your
Audio/Video component.
If the Audio/Video component does not turn off, try a different two digit preset code.
6. The remote will now control your Audio/Video component.
7. Repeat steps 1 - 6 it you wish to program the remote to control another Audio/Video component.
Be sure to use a different
A/V button on the remote, since only one component can be programmed per button.