Hitachi CC14SF Instruction Manual - Page 10

Standard Accessories, Warning, Preparation Before Operation - power tools

Get Hitachi CC14SF - Power Tools 14'' Heavy-Duty Cut-Off Saw PDF manuals and user guides
UPC - 717709010413
View all Hitachi CC14SF manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

English STANDARD ACCESSORIES 2 1 Cut-Off Wheel 14" × 7/64" × 1"(355 × 2.8 × 25.4 mm) 1pc. (Code No.) (Attached to the main body) 2 Hex. bar wrench Fig. 3 WARNING: The use of attachment or accessories not recommended in this manual may be hazardous. PREPARATION BEFORE OPERATION Make the following preparations before operating the power tool: 1. Installation The machine may be bolted (2 bolts) down to a level location using the bolt holes in the base. 2. Extension Cord. Ampere rating (on nameplate) 12.1 to 16.0 To use the power tool when no suitable power source is nearby, use an extension cord of suitable size to ensure safety, and to prevent Ext. cord length Wire gauge size A.W.G (mm2) power loss and overheating. Determine from the accompanying table the 25 ft (7.5 m) 50 ft. (15 m) 100 ft. (30.5 m) 14 A.W.G (2.0 mm2) 12 A.W.G (3.5 mm2) Not recommended required extension cord wire size. Check power cord and extension cords for loose or exposed wires and damaged insulation, before using. Repair or replace as needed, before using the power tool. NOTE: The lower the wire size number, the heavier the wire, and the farther it will carry current without a voltage drop. WARNING: Never connect this unit to an electrical power source until all operating instructions have been read and understood. 3. Take off the chain. As the movable part is pulled down by a chain when shipping out, slightly push the handle down and take off the chain from the handle. 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
English
10
Ampere rating
12.1 to 16.0
(on nameplate)
Ext. cord length
Wire gauge size
A.W.G (mm
2
)
25 ft
14 A.W.G
(7.5 m)
(2.0 mm
2
)
50 ft.
12 A.W.G
(15 m)
(3.5 mm
2
)
100 ft.
Not
(30.5 m)
recommended
STANDARD ACCESSORIES
1
Cut-Off Wheel 14"
×
7/64"
×
1"(355
×
2.8
×
25.4 mm)
1pc. (Code No.)
(Attached to the main body)
2
Hex. bar wrench
Fig. 3
WARNING:
The use of attachment or accessories not recommended in this manual
may be hazardous.
PREPARATION BEFORE OPERATION
Make the following preparations before operating the power tool:
1. Installation
The machine may be bolted (2 bolts) down to a level location using the bolt holes in the
base.
2. Extension Cord.
To use the power tool when no suitable power
source is nearby, use an extension cord of
suitable size to ensure safety, and to prevent
power loss and overheating.
Determine from the accompanying table the
required extension cord wire size.
Check power cord and extension cords for loose
or exposed wires and damaged insulation,
before using.
Repair or replace as needed, before using the
power tool.
NOTE:
The lower the wire size number, the heavier the wire, and the farther it will carry
current without a voltage drop.
WARNING:
Never connect this unit to an electrical power source until all operating
instructions have been read and understood.
3. Take off the chain.
As the movable part is pulled down by a chain when shipping out, slightly push the
handle down and take off the chain from the handle.
2