Hitachi CP X206 User Manual - Page 54

NETWORK Menu - user manual

Get Hitachi CP X206 - XGA LCD Projector PDF manuals and user guides
UPC - 050585151451
View all Hitachi CP X206 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

NETWORK Menu NETWORK Menu Remember that incorrect network settings on this projector may cause trouble on the network. Be sure to consult with your network administrator before connecting to an existing access point on your network. From the NETWORK menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ►cursor button or ENTER button to execute the item. Then perform it according to the following table. See the User's Manual - Network Guide for details of NETWORK operation. NOTE • If you are not utilizing SNTP ( Date/Time Settings of the User's Manual - Network Guide), then you must set the DATE AND TIME (55) during the initial installation. • The network communication control is disabled while the projector is in standby mode if the STANDBY MODE item of SETUP menu is set to SAVING. Please connect the network communication to the projector after setting the STANDBY MODE to NORMAL (35). Item Description Selecting this item displays the SETUP Menu for the network. Use the ▲/▼ buttons to select an item, and the ► or ENTER button on the remote control to perform the item. SETUP DHCP (Dynamic Host Configuration Protocol) Use the ▲/▼ buttons to turn DHCP on/off. ON  OFF Select OFF when the network does not have DHCP enabled. • When the "DHCP" setting changes to "ON", it takes a little time to obtain IP address from DHCP server. • Auto IP function will be assigned an IP address if the projector could not obtain an IP address from server even if DHCP is "ON". (continued on next page) 54

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
54
Remember that incorrect network settings on this projector
may cause trouble on the network. Be sure to consult with
your network administrator before connecting to an existing
access point on your network.
From the NETWORK menu, items shown in the table below
can be performed.
Select an item using the ▲/▼ cursor buttons, and press the ►cursor button or
ENTER
button to execute the item. Then perform it according to the following
table.
See the User’s Manual - Network Guide for details of NETWORK operation.
NETWORK Menu
NETWORK Menu
• If you are not utilizing SNTP
(
Date/Time Settings of the User’s
Manual - Network Guide)
, then you must set the DATE AND TIME (
55
)
during the initial installation.
• The network communication control is disabled while the projector is in
standby mode if the STANDBY MODE item of SETUP menu is set to SAVING.
Please connect the network communication to the projector after setting the
STANDBY MODE to NORMAL (
35
).
NOTE
Item
Description
SETUP
Selecting this item displays the SETUP Menu
for the network.
Use the ▲/▼ buttons to select an item, and
the ► or
ENTER
button on the remote control
to perform the item.
DHCP
(Dynamic
Host
Configuration
Protocol)
Use the ▲/▼ buttons to turn DHCP on/off.
ON
ó
OFF
Select OFF when the network does
not have DHCP enabled.
• When the “DHCP” setting changes to “ON”, it takes a
little time to obtain IP address from DHCP server.
• Auto IP function will be assigned an IP address if the
projector could not obtain an IP address from server
even if DHCP is “ON”.
(continued on next page)