Hitachi CP-X505W User Manual - Page 53

Description, Dynamic Host, Protocol, IP ADDRESS, SUBNET MASK, DEFAULT, GATEWAY, User's Manual -

Get Hitachi CP-X505W PDF manuals and user guides View all Hitachi CP-X505W manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

NETWORK Menu NETWORK Menu Consult with your network administrator before connecting to an /'07=4)$? 5'.'%6 existing access point on your network. Incorrect network settings 2+%674' &*%2 674010 on this projector may cause trouble on the network. +/#)' +0276 +2#&&4'55 57$0'6/#5- Select "NETWORK" from the main menu to access the following 5'672 #7&+1 functions. 5%4''0 &'(#7.6)#6'9#; 6+/'&+(('4'0%' '#0&6+/' Select an item using the ▲/▼ cursor buttons on the projector or 126+10 0'6914- G5*16 +0(14/#6+10 remote control, and press the ► cursor button on the projector or '#5;/'07 5'48+%' remote control, or ENTER button on the remote control to execute the item. Then perform it according to the following table. NOTE • The factory default setting for DHCP is "TURN ON". There is no need to set up [DHCP], [IP ADDRESS], [SUBNET MASK] or [DEFAULT GATEWAY] if your network has DHCP enabled. ( User's Manual - Network Functions) • If you are not utilizing SNTP ( User's Manual - Network Functions), then you must set the DATE AND TIME during the initial installation. Please refer to the item DATE AND TIME on the following list. Item Description DHCP (Dynamic Host Configuration Protocol) DHCP TURN ON/TURN OFF: Use the ▲/▼ buttons to turn DHCP on/off TURN ON  TURN OFF &*%2 674010 67401(( Select TURN OFF when the network does not have DHCP enabled. IP ADDRESS Entering the IP ADDRESS : Use the buttons to enter the IP ADDRESS. This function can only be used when DHCP is set to "TURN OFF". 192. 168. 1. 254 IP ADDRESS • The IP ADDRESS is the number that identifies this projector on the network. You cannot have two devices with the same IP ADDRESS on the same network. SUBNET MASK Entering the SUBNET MASK : Use the buttons to enter the same SUBNET MASK used by your PC. This function can only be used when DHCP is set to "TURN OFF". 255. 255. 255. 0 SUBNET MASK DEFAULT GATEWAY Entering the DEFAULT GATEWAY : Use the buttons to enter the DEFAULT GATEWAY (a node on a computor network that serves as an access point to another network) address.This function can only be used when DHCP is set to "TURN OFF". 0. 0. 0. 0 DEFAULT GATEWAY (continued on next page) 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
53
NETWORK Menu
NETWORK Menu
Item
Description
DHCP
(Dynamic Host
Configuration
Protocol)
DHCP TURN ON/TURN OFF:
Use the ▲/▼ buttons to turn DHCP on/off
TURN ON
ó
TURN OFF
Select TURN OFF when the network does not have
DHCP
enabled.
IP ADDRESS
Entering the IP ADDRESS :
Use the
▲/▼/◄/► buttons to enter the IP
ADDRESS. This function can only be used
when DHCP is set to “TURN OFF”.
•
The IP ADDRESS is the number that identifies this projector
on the network. You cannot have two devices with the same IP
ADDRESS on the same network.
SUBNET MASK
Entering the SUBNET MASK :
Use the
▲/▼/◄/► buttons
to enter the
same SUBNET MASK used by your PC.
This function can only be used when DHCP
is set to “TURN OFF”.
DEFAULT
GATEWAY
Entering the DEFAULT GATEWAY :
Use the
▲/▼/◄/►
buttons to enter the
DEFAULT GATEWAY (a node on a computor
network that serves as an access point to
another network) address.This function can only
be used when DHCP is set to “TURN OFF”.
Consult with your network administrator before connecting to an
existing access point on your network. Incorrect network settings
on this projector may cause trouble on the network.
Select “NETWORK” from the main menu to access the following
functions.
Select an item using the ▲/▼ cursor buttons on the projector or
remote control, and press the ► cursor button on the projector or
remote control, or ENTER button on the remote control to execute
the item. Then perform it according to the following table.
NOTE
• The factory default setting for DHCP is “TURN ON”. There is no need to set
up [DHCP], [IP ADDRESS], [SUBNET MASK] or [DEFAULT GATEWAY] if your network
has DHCP enabled.
(
User’s Manual - Network Functions)
• If you are not utilizing SNTP
(
User’s Manual - Network Functions)
, then you must
set the DATE AND TIME during the initial installation. Please refer to the item DATE
AND TIME on the following list.
192. 168.
254
IP ADDRESS
1.
255. 255.
0
SUBNET MASK
255.
0.
0.
0
DEFAULT GATEWAY
0.
(continued on next page)