Hitachi DH25PB Instruction Manual - Page 17

Maintenance And Inspection

Get Hitachi DH25PB - 31/32inch SDS-plus Shank Rotary Hammer PDF manuals and user guides
UPC - 717709007611
View all Hitachi DH25PB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

English MAINTENANCE AND INSPECTION WARNING: Be sure to switch power OFF and disconnect the plug from the receptacle during maintenance and inspection. 1. Inspecting the drill bits Since use of a dull tool will cause motor malfunctioning and degraded efficiency, replace the drill bit with a new one or resharpening without delay when abrasion is noted. 2. Inspecting the screws Regularly inspect all screws and ensure that they are properly tightened. Should any of the screws be loosened, retighten them immediately. WARNING: Using this rotary hammer with loosened screws is extremely dangerous. 3. Maintenance of the motor The motor unit winding is the very "heart" of the power tool. Exercise due care to ensure the winding does not become damaged and/or wet with oil or water. 4. Inspecting the carbon brushes: (Fig. 18) The motor employs carbon brushes which are consumable parts. When they become worn to or near "wear limit", it could result in motor trouble. When an auto-stop carbon brush is equipped, the motor will stop automatically. At that time, replace both carbon brushes with new ones which have the same carbon brush Nos. shown in the figure. In addition, always keep carbon brushes clean and ensure that they slide freely within the brush holders. CAUTION: Using this rotary hammer with a carbon brush which is worn in excess of the wear limit will damage the motor. Wear limit a 0.47" (12 mm) No. of carbon brush Usual carbon brush Auto-stop carbon brush a 0.2" (5 mm) No. of carbon brush 21 - 70 Fig. 18 NOTE: Use HITACHI carbon brush No. indicated in Fig. 18. 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
English
17
MAINTENANCE AND INSPECTION
WARNING:
Be sure to switch power OFF and disconnect the plug from the
receptacle during maintenance and inspection.
1.
Inspecting the drill bits
Since use of a dull tool will cause motor malfunctioning and degraded efficiency, replace
the drill bit with a new one or resharpening without delay when abrasion is noted.
2.
Inspecting the screws
Regularly inspect all screws and ensure that they are properly tightened. Should any of
the screws be loosened, retighten them immediately.
WARNING:
Using this rotary hammer with loosened screws is extremely
dangerous.
3.
Maintenance of the motor
The motor unit winding is the very
“
heart
”
of the power tool. Exercise due care to
ensure the winding does not become damaged and/or wet with oil or water.
4.
Inspecting the carbon brushes: (Fig. 18)
The motor employs carbon brushes which are consumable parts. When they become
worn to or near
“
wear limit
”
, it could result in motor trouble. When an auto-stop carbon
brush is equipped, the motor will stop automatically. At that time, replace both carbon
brushes with new ones which have the same carbon brush Nos. shown in the figure.
In addition, always keep carbon brushes clean and ensure that they slide freely within
the brush holders.
CAUTION:
Using this rotary hammer with a carbon brush which is worn in excess of the wear
limit will damage the motor.
Fig. 18
NOTE:
Use HITACHI carbon brush No. indicated in Fig. 18.
a
No. of
carbon brush
Usual carbon
0.2"
21
brush
(5 mm)
Auto-stop
—
70
carbon brush
Wear limit
No. of carbon brush
0.47"
(12 mm)
a