Hitachi DV18DCL Instruction Manual - Page 18

Only Hitachi STANDARD ACCESSORIES phillips

Get Hitachi DV18DCL - 18V 1.5Ah Lithium Ion Hammer Drill PDF manuals and user guides
UPC - 717709013025
View all Hitachi DV18DCL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

English 13. Using the hook (Hook with bit holder) WARNING: When using the hook, pay sufficient attention so that the main equipment does not fall. If the tool falls, there is a risk of accident. CAUTION: ● Do not attach the tip tool except phillips bit to the tool main unit when carrying the tool main unit with the hook suspended from a waist belt. Injury may result if you carry the equipment suspended from the waist belt with sharp tipped components such as drill bit attached. The hook can be installed on the right or left side and the angle can be adjusted in 5 steps between 0° and 80°. (1) Operating the hook (a) Pull out the hook toward you in the direction of arrow (A) and turn in the direction of arrow (B) (Fig. 14). (b) Remove the hook and spring (Fig. 16). Hook Spring Fig. 16 (c) Install the hook and spring on the other side and securely fasten with screw (Fig. 15). NOTE: Pay attention to the spring orientation. Install the spring with larger diameter away from you (Fig. 17). Screw Hook Fig. 14 (b) The angle can be adjusted in 5 steps (0°, 20°, 40°, 60°, 80°). Adjust the angle of the hook to the desired position for use. (2) Switching the hook position CAUTION: ● If the tool falls, there is a risk that malfunction and/ or physical damage can occur. It is recommended that you also use fall-preventing wires, etc. ● Incomplete installation of the hook may result in bodily injury when used. Larger diameter faces away Fig. 17 14. Using the bit holder (Hook with bit holder) ⅜ Installing the bit Slide the bit from the side, and then insert firmly until the groove on the bit locks in the protruded section of the hook. ⅜ Removing the bit Securely hold the main unit and pull out the bit by holding the tip with your thumb (Fig. 18). (a) Securely hold the main unit and remove the screw using a slotted head screwdriver or a coin (Fig. 15). Fig. 18 Loosen CAUTION: ● Only Hitachi STANDARD ACCESSORIES phillips bit (No. 2 × 65L; Code No. 983006) may be used. Do not use other bits since they may come loose. Screw 18 Fig. 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
English
18
13.
Using the hook (Hook with bit holder)
WARNING:
When using the hook, pay sufficient attention so
that the main equipment does not fall. If the tool
falls, there is a risk of accident.
CAUTION:
●
Do not attach the tip tool except phillips bit to the
tool main unit when carrying the tool main unit
with the hook suspended from a waist belt.
Injury may result if you carry the equipment
suspended from the waist belt with sharp tipped
components such as drill bit attached.
The hook can be installed on the right or left side
and the angle can be adjusted in 5 steps between
0° and 80°.
(1)
Operating the hook
(a)
Pull out the hook toward you in the direction
of arrow (A) and turn in the direction of arrow
(B) (Fig. 14).
(b)
The angle can be adjusted in 5 steps (0°, 20°,
40°, 60°, 80°).
Adjust the angle of the hook to the desired
position for use.
(2)
Switching the hook position
CAUTION:
●
If the tool falls, there is a risk that malfunction and/
or physical damage can occur. It is recommended
that you also use fall-preventing wires, etc.
●
Incomplete installation of the hook may result in
bodily injury when used.
(a)
Securely hold the main unit and remove the
screw using a slotted head screwdriver or a
coin (Fig. 15).
(b)
Remove the hook and spring (Fig. 16).
(c)
Install the hook and spring on the other side
and securely fasten with screw (Fig. 15).
NOTE:
Pay attention to the spring orientation. Install the
spring with larger diameter away from you (Fig.
17).
14.
Using the bit holder (Hook with bit holder)
±
Installing the bit
Slide the bit from the side, and then insert firmly
until the groove on the bit locks in the protruded
section of the hook.
±
Removing the bit
Securely hold the main unit and pull out the bit by
holding the tip with your thumb (Fig. 18).
CAUTION:
●
Only Hitachi STANDARD ACCESSORIES phillips
bit (No. 2
×
65L; Code No. 983006) may be used.
Do not use other bits since they may come loose.
Fig. 14
Hook
Fig. 15
Loosen
Screw
Screw
Fig. 17
Larger diameter faces away
Fig. 16
Spring
Hook
Fig. 18