Hitachi W6VB3SD Instruction Manual - Page 12

How To Use The Screw Driver

Get Hitachi W6VB3SD - 2,600 RPM SUPERDRIVE Collated Screw System PDF manuals and user guides
UPC - 754005008720
View all Hitachi W6VB3SD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

English 8. Mounting the bit For details, refer to the item "Mounting and dismounting the hex-socket or the bit". 0.04" - 0.06" (1 - 1.5 mm) Self-drilling screw Sub-Stopper (F) Fig. 6 HOW TO USE THE SCREW DRIVER 1. Switch operation and rotational speed adjustment Bit rotational speed can be adjusted between 0-6000/min (W6VM) or 0-4500/min (W6V4) or 0-3000/min (W6VA4) or 0-2600/min (W6VB3) or 0-1700/min (W8VB2) varying the degree by which the trigger switch is pulled. Rotational speed increases as the trigger switch is pulled, and reaches a maximum speed of 6000/min (W6VM) or 4500/min (W6V4) or 3000/min (W6VA4) or 2600/min (W6VB3) or 1700/min (W8VB2) when the trigger switch is pulled fully. To facilitate continuous operation, pull the trigger switch and depress the switch stopper. The switch will then remain ON even when the finger is released. By pulling the trigger switch again, the switch stopper disengages and the switch is turned OFF when the trigger switch is released. 2. Screw Driver operation When the switch is turned ON, the motor starts to run but the hex-socket (or the bit) does not rotate. Attach the hex-socket to the screw head groove, and push the Screw Driver against the screw. The hex-socket then rotates and tightens the screw. CAUTION Ensure that the Screw Driver is held truly perpendicular to the head of the screw. If held at an angle, the driving force will not be fully transferred to the screw, and the screw head and/or hex-socket will be damaged. Hex-socket rotation stops when pushing force is released. 3. Direction of hex-socket rotation The hex-socket rotates clockwise (viewed from the rear side) when the reversing switch lever is set to the "R" side position. When the lever is set to the "L" side position, the hex-socket rotates counterclockwise, and can be used to loosen and remove screws. CAUTION Never change the direction of hex-socket (or bit holder) rotation while the motor is running. To do so would seriously damage the motor. Turn the power switch OFF before changing the direction of hex-socket (or bit holder) rotation. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
12
English
8.
Mounting the bit
For details, refer to the item “Mount-
ing and dismounting the hex-socket or
the bit”.
HOW TO USE THE SCREW DRIVER
1.
Switch operation and rotational speed adjustment
Bit rotational speed can be adjusted between 0–6000/min (W6VM) or 0–4500/min
(W6V4) or 0–3000/min (W6VA4) or 0–2600/min (W6VB3) or 0–1700/min (W8VB2)
varying the degree by which the trigger switch is pulled. Rotational speed increases
as the trigger switch is pulled, and reaches a maximum speed of 6000/min (W6VM)
or 4500/min (W6V4) or 3000/min (W6VA4) or 2600/min (W6VB3) or 1700/min (W8VB2)
when the trigger switch is pulled fully.
To facilitate continuous operation, pull the trigger switch and depress the switch
stopper. The switch will then remain ON even when the finger is released. By
pulling the trigger switch again, the switch stopper disengages and the switch is
turned OFF when the trigger switch is released.
2.
Screw Driver operation
When the switch is turned ON, the motor starts to run but the hex-socket (or the
bit) does not rotate. Attach the hex-socket to the screw head groove, and push
the Screw Driver against the screw. The hex-socket then rotates and tightens the
screw.
CAUTION
Ensure that the Screw Driver is held truly perpendicular to the head of the screw.
If held at an angle, the driving force will not be fully transferred to the screw,
and the screw head and/or hex-socket will be damaged. Hex-socket rotation
stops when pushing force is released.
3.
Direction of hex-socket rotation
The hex-socket rotates clockwise (viewed from the rear side) when the revers-
ing switch lever is set to the “R” side position. When the lever is set to the “L”
side position, the hex-socket rotates counterclockwise, and can be used to loosen
and remove screws.
CAUTION
Never change the direction of hex-socket (or bit holder) rotation while the mo-
tor is running. To do so would seriously damage the motor. Turn the power
switch OFF before changing the direction of hex-socket (or bit holder)
rotation.
Fig. 6
0.04" – 0.06"
(1 – 1.5 mm)
Self-drilling screw
Sub-Stopper (F)