Hitachi X995 User Manual - Page 23

Symptom

Get Hitachi X995 - CP XGA LCD Projector PDF manuals and user guides View all Hitachi X995 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

TROUBLESHOOTING (continued) Symptom Before requesting repair, check in accordance with the following chart. If the situation cannot be corrected, then contact your dealer. Table 11. Symptom Symptom Possible cause Remedy Page The main power switch is not turned on. Turn on the main power switch. 8,9 The power cord is Plug the power cord into an AC The power is not disconnected. power outlet. turned on. Turn off the projector with the main The main power was power switch (set the power switch disconnected during operation to [O]), and wait for about 20 9 by the power failure and so on. minutes. When the equipment has cooled enough, turn power on. The input is not correctly set. No video or audio. Use the projector or remote control transmitter to set. 10 No signal input. Connect correctly. 7,8 The projector is not correctly connected. Video is present but no audio. The volume is set to minimum. Connect correctly. Press VOLUME on the remote control or display the menu screen and adjust the volume. 7,8 11,15 Mute is turned on. Press the MUTE button. 11 The projector is not correctly connected. Connect correctly. 7,8 Audio is present but The brightness adjustment knob Select BRIGHT with the MENU no video. is rotated fully clockwise. button and the press the button. 12 The lens cap is still attached. Remove the lens cap. Colors are pale and Color density and color color matching is matching are not correctly poor. adjusted. Adjust the video. Images are dark. Brightness and contrast are not correctly adjusted. Adjust the video. The lamp is nearing the end of its service life. Replace with a new lamp. Video is blurred. Focus or H PHASE is out of adjustment. Adjust the focus or H PHASE. 9 12 12 17 9,12 ENGLISH-22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
ENGLISH-22
ENGLISH-22
T
T
R
R
O
O
U
U
B
B
L
L
E
E
S
S
H
H
O
O
O
O
T
T
I
I
N
N
G
G
(
(
c
c
o
o
n
n
t
t
i
i
n
n
u
u
e
e
d
d
)
)
Symptom
Before requesting repair, check in accordance with the following chart. If the situation cannot be
corrected, then contact your dealer.
Table 11. Symptom
Symptom
Possible cause
Remedy
Page
The power is not
turned on.
The main power switch is not
turned on.
Turn on the main power switch.
8,9
The power cord is
disconnected.
Plug the power cord into an AC
power outlet.
The main power was
disconnected during operation
by the power failure and so on.
Turn off the projector with the main
power switch (set the power switch
to [O]), and wait for about 20
minutes. When the equipment has
cooled enough, turn power on.
9
No video or audio.
The input is not correctly set.
Use the projector or remote control
transmitter to set.
10
No signal input.
Connect correctly.
7,8
Video is present but
no audio.
The projector is not correctly
connected.
Connect correctly.
7,8
The volume is set to minimum.
Press VOLUME
on the remote
control or display the menu screen
and adjust the volume.
11,15
Mute is turned on.
Press the MUTE
button.
11
Audio is present but
no video.
The projector is not correctly
connected.
Connect correctly.
7,8
The brightness adjustment knob
is rotated fully clockwise.
Select BRIGHT with the MENU
button and the press the
button.
12
The lens cap is still attached.
Remove the lens cap.
9
Colors are pale and
color matching is
poor.
Color density and color
matching are not correctly
adjusted.
Adjust the video.
12
Images are dark.
Brightness and contrast are not
correctly adjusted.
Adjust the video.
12
The lamp is nearing the end of
its service life.
Replace with a new lamp.
17
Video is blurred.
Focus or H PHASE is out of
adjustment.
Adjust the focus or H PHASE.
9,12