Holmes HCM730 Product Manual - Page 2

4.

When full, carry the tank to the humidifier and place it

into the housing. To insert

tank into housing, use the

locating tabs at the bottom

of the unit to line up the

base of the tank evenly

with housing at a slight

angle. Once the tank is

lined up at the base, use

the handle to push the top

of the tank into place. You

will hear a click when tank

is locked in correctly. The

tank holds 1.2 gallons of

water. The tank will immediately begin to empty into the

base. (See Figure 6)

NOTE:

You may hear a “gurgling noise” as tank fills.

This is completely normal.

5.

Plug the power cord into a 120V AC electrical outlet.

OPERATING INSTRUCTIONS

NOTE:

The humidifier produces clean, cool, INVISIBLE

moisture. It is normal not to see the moisture.

1. Allow up to 30 minutes for the filter to fully absorb water

and the unit to produce the maximum moisture output.

2. Press the Power Button (

) to turn the humidifier on,

the humidifier will run at High setting and "3" will

illuminate on the display. After 2 seconds, the display will

return to show the room humidity.

3. If you want to switch to Medium/Low settings, press the Power

Button (

) again. Each press of the button will cycle

through the speed settings (High-Medium-Low-Off), and the

selected setting (3-2-1-OF) will appear on the display.

4. To shut the humidifier off at any setting, press and hold

the Power Button (

) for 3 seconds and “OF” will

illuminate on the display.

Digital Humidistat Control

Your humidifier is equipped with a digital humidistat that

allows you to set your humidifier to your desired comfort

level by pressing the up/down buttons(

) to adjust the

humidity level ranging from 30% to 60%. The selected

humidity level will illuminate on the display.

NOTE:

For the most accurate humidity reading, run your

humidifier for 1 hour before reading the humidistat.

When the room humidity level rises above the set humidity,

the humidifier will stop. When the room humidity level drops

below the set humidity, the humidifier will turn on

automatically to maintain the preset humidity level.

WARNING: DO NOT

move the humidifier with water in

the tank or the humidifier base. The moving action of the

water may activate the water tank’s release nozzle and

overfill the humidifier base. This may cause the humidifier to

function intermittently, or stop emitting mist. Should this

occurs, simply remove the excess water from the humidifier

base.

NOTES:

PLEASE READ AND SAVE THESE

IMPORTANT SAFETY INSTRUCTIONS

FEATURES - OPERATIONS

•

High

setting is ideal for overly dry environments where

faster moisture relief is desired.

This setting allows the fan

to operate at its full capacity to produce the maximum

moisture level.

Low

setting will produce the longest run

time and have a quieter performance which is ideal for

sleeping and when desiring more quiet environments.

• Allow up to 30 minutes for the filter to fully absorb water

and for the unit to produce moisture.

Timer

Your humidifier is equipped with 24-Hour Auto Shut-off Timer

feature. This allows you to program your humidifier to shut

off automatically after running a defined time interval.

1. Press the Timer Button (

) once. The

“0”

will

illuminate on display.

2. Press the up/down buttons (

) to adjust from

0

to

24

to select your desired time interval for the humidifier

to shut-off automatically.

3. The selected hour will appear on the display.

4. When timer is set, you may check the remaining time

while humidifier is still in operation. Press the Timer

Button and the remaining time (e.g., 7) will illuminate on

the display.

5. To cancel the Timer feature, press the

Timer Button

(

). The remaining time will appear on the screen.

Press the down button to “0”. The Timer will then be

cancelled.

NOTE:

When the water tank is empty, and the base is

almost empty, you need to refill the tank. The fan will

continue to run to help dry the humidifier. Shut off and

unplug the unit. Please follow the Daily Cleaning Instructions.

Refill the tank as directed in Filling the Water Tanks

Instructions.

NOTE:

If moisture forms on the walls or windows, turn off

the humidifier.

REPLACING THE FILTERS

Through normal use, waterborne minerals and sediment

become trapped in the wick filter. The harder your water, the

greater the amount of minerals in the water, and the more

often you will need to change your filter.

You will be able to monitor the life of the filter in your

humidifier by checking the FilterCheck

®

Indicator.

NOTE:

After 30 minutes of use, FilterCheck

®

Indicator will

move and indicate your filter condition.

A brand new filter will register in the section reading GOOD

filter. After frequent use of your humidifier, the FilterCheck

®

Indicator will let you know when the filters need to be

changed. (See Figure 8)

When the needle is in the CHANGE section, this means the

proper amount of moisture is not getting into your air due to

the excessive minerals and sediment that have become

trapped on your filters. At this point, you should replace your

filter. It is important to change your filter as indicated to

obtain stated performance level.

To replace the filter, follow the steps below:

1.

Turn the unit off and disconnect from the electrical outlet.

2.

Remove the tank from the housing.

3.

Unlock the housing from the base by turning the lock

knob to the unlocked position. (See Figure 9)

4.

Lift the housing straight up and place to the side.

5.

Unlock the wick holder from the base by turning the lock

knob to the unlocked position.

6.

Remove the wicks from the wick holder. (See Figure 10)

7.

Follow the weekly cleaning instructions.

PRODUCT NOTICES

1. If moisture forms on the walls or windows of the room,

turn off the humidifier. The room already has plenty of

humidity and additional moisture may cause damage.

2.

Always place humidifier on a firm, flat, level surface. A

waterproof mat or pad is recommended for use under

the humidifier. NEVER place it on a rug or carpet, or on a

finished floor that may be damaged by exposure to

water or moisture.

3.

DO NOT allow the Moisture Outlet to directly face the wall.

Moisture could cause damage, particularly to wall paper.

4.

To prevent damage to surfaces, do not place humidifier

under overhanging surfaces.

Cord and Plug Instructions:

The length of cord used on this appliance was selected to

reduce the hazards of becoming tangled in, or tripping over a

longer cord. If a longer cord is necessary an approved

extension cord may be used. The electrical rating of the

extension cord must be equal to or greater than the rating of

the humidifier (refer to the rating information placed on the

humidifier). Care must be taken to arrange the extension cord

so that it will not drape over the countertop or tabletop where

it can be pulled on by children or accidentally tripped over.

HOW COOL MIST WORKS

Your Holmes

®

Cool Mist humidifier draws dry air through the

rear air intake grill area. This air is then passed through a

moisture–laden wick filter, which retains the minerals and

deposits in the water. The resulting moist air is directed back

into the room from the top air grill.

NOTE:

This humidification system provides a cool, invisible

moisture output. It is normal not to see the mist.

NOTE:

A humidity level below 20% can be unhealthy and

uncomfortable. The recommended humidity level is between

40%-50%.

PRE-OPERATING INSTRUCTIONS

1.

Be sure the humidifier is

switched to OFF and the

unit is disconnected from

the electrical outlet.

2.

Select a location for your

humidifier, on a flat

surface, about 4 inches

(10 cm) away from the

wall. DO NOT place the

humidifier on a finished

floor or near furniture,

which can be damaged by

too much moisture or

water. Place on a moisture

resistant surface.

NOTE:

The first time you use your

humidifier, saturate your wick filter

and run the humidifier for 30

minutes before reading the filter

meter. This will ensure that you

receive the most accurate reading

upon your first use.

FILLING THE WATER TANK

1.

Remove the tank from the

housing of the humidifier

by grabbing the handle of

the tank and pulling the

tank out of the housing

and then bring the tank to

the faucet. (See Figure 3)

2.

Turn the tank upside down

and twist off the tank cap

by turning counter

clockwise. Fill tank with

cool, fresh tap water. DO

NOT fill with warm water

as this may cause leaking.

(See Figure 4)

3.

To Replace the cap on

tank, align arrows and

turn to align to lock

position. Ensure tank is

closed FIRMLY. (See Figure 5)

When using electrical appliances, basic safety precautions

should always be followed to reduce the risk of fire, electric

shock, and injury to persons, including the following:

1.

Read all instructions before using the appliance.

2.

To avoid fire or shock hazard, plug the appliance directly

into a 120V AC electrical outlet.

3.

Keep the cord out of heavy traffic areas. To avoid fire hazard,

NEVER put the cord under rugs or near heat registers.

4.

DO NOT place humidifier near heat sources such as stoves,

radiators, and heaters. DO locate your humidifier on an

inside wall near an electrical outlet. The humidifier should be

at least 4 inches (10 cm) away from the wall for best results.

5.

NEVER place humidifier in an area where it is accessible to

children. NEVER use humidifier in a closed room, particularly

where a child may be sleeping, resting, or playing (a closed

room may result in excessive humidity).

6.

Do not attempt to refill humidifier without first unplugging

the unit from its electrical outlet. Failure to heed this

warning may cause personal injury. Be sure to unplug the

unit by pulling on the plug and not the cord.

7.

Never place anything over moisture outlet when the unit

is running.

8.

NEVER drop or insert any object into any openings.

9.

DO NOT operate any appliance with a damaged cord or

plug, after the appliance malfunctions, or if it has been

dropped or damaged in any manner. Return appliance to

manufacturer for examination, electrical or mechanical

adjustment, or repair.

10.

Use appliance only for intended household use as described

in this manual. Any other use not recommended by the

manufacturer may cause fire, electric shock, or injury to

persons. The use of attachments not recommended or sold

by the manufacturer may cause injury.

11.

DO NOT use outdoors.

12.

Humidifier should be unplugged when not in use.

13.

NEVER tilt, move, or attempt to empty unit while it is

operating. Shut off and unplug before removing the

water tank and moving the unit.

14.

This humidifier requires daily and weekly maintenance

to operate appropriately. Refer to daily and weekly

cleaning procedures. Use only cleaners and additives

recommended by the manufacturer.

15.

NEVER use detergents, gasoline, glass cleaner, furniture

polish, paint thinner, or other household solvents to

clean any part of the humidifier.

16.

Do not use humidifier in an area where humidity level is

in excess of 50%. Use a hygrometer, available at your

local retailer or through the manufacturer, to measure

the humidity.

17.

DO NOT attempt to repair or adjust any electrical or

mechanical functions on this unit.

Doing so will void

your warranty.

The inside of the unit contains no user

serviceable parts. All servicing should be performed by

qualified personnel only.

18.

Never place housing under water flow or immerse in liquids.

19.

Do not plug in the cord with wet hands: electric shock

could result.

20.

Do not pour water in any openings other than the water

tank.

21.

NEVER operate unit without water in the tank.

22.

Do not move unit after it has been used until unit cools

completely.

23.

Use both hands when carrying full tank of water.

PLEASE READ AND SAVE

THESE IMPORTANT SAFETY

INSTRUCTIONS




CLEANING / MAINTENANCE

THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the

other). To reduce the risk of electric shock, this plug is intended to fit in a

polarized outlet only one way. If the plug does not fit fully in the outlet,

reverse the plug. If it still does not fit, contact a qualified electrician to

install the proper outlet.

DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS

SAFETY FEATURE IN ANY WAY.

A.

Humidifier Housing

B.

Control Panel

C.

FilterCheck

®

Indicator

D. Tank Lock

E.

Tank Handle

F.

Tank

G.

Tank Cap (not shown)

H. Wick Filters (2)

I.

Lock Knobs (2)

J.

Base

K.

Wick Filter Holder

Figure 7

Control Panel

F

A

B

C

D

E

H

I

K

G

J

Figure 3

Figure 6

Figure 2

10 cm

10 cm

Figure 1

Figure 4

Figure 5

Figure 10

Figure 9

Figure 8

8.

Insert new filters into the wick holder and lock the wick

holder back onto the base.

9.

Replace the housing onto the base and lock it into place.

10. Fill the tank and place back into housing, you will hear

a click sound when the tank is locked on the housing

properly.

11. Repeat Operating Instructions.

It will take about 30 minutes for the humidifier to reach

maximum output.

NOTE:

You can purchase replacement filters (model

BWF100) at a local retailer, by calling 1-800-546-5437,

or by visiting

www.holmesproducts.com

. It is

recommended that a replacement filter is purchased for

uninterrupted use.

CLEANING AND MAINTENANCE

INSTRUCTIONS

Humidifiers provide comfort by adding moisture to dry,

heated indoor air. To benefit most from the humidifier

and avoid product misuse, follow all instructions

carefully. Please note that this is an electrical appliance

and requires attention when in use.

In addition, if you do not follow the recommended care

and maintenance guidelines, micro-organisms may be

able to grow in the water within the water tank. You

must routinely follow the cleaning procedures that follow

in order to ensure proper, efficient operation of your

humidifier. Proper maintenance and cleaning is essential

to the continued performance of your unit and the

avoidance of algae or bacteria build-up.

Daily Maintenance

1.

Be sure the unit is OFF and is disconnected from the

electrical outlet.

2.

Remove the housing and the tank from the humidifier

and place in sink or tub.

3.

Carry the base of the unit to the sink, remove the wick,

place in sink, drain any remaining water and rinse

thoroughly to remove any sediment or dirt. Wipe clean,

and dry with a clean cloth or paper towel.

4.

Drain the water from the tank into the sink and rinse

tank thoroughly. Wipe clean, and dry with a clean cloth

or paper towel.

5.

Put filters back into wick holder making sure the rivet

attaches to the holder. Lock the wick holder back into

place. Replace the housing and lock it into place. Refill

the tank with cool tap water as instruction earlier in the

filling instructions. Do not overfill.

6.

Follow Operating Instructions.

NOTE:

The Tray is dishwasher safe (TOP RACK ONLY)

for easy cleaning.

Weekly Maintenance

To Remove Scale:

1.

Repeat steps 1-4 above.

2.

Clean the base by partially filling the base with one 8-oz

cups of undiluted white vinegar. Leave this solution in the

base for 20 minutes, while cleaning all the interior

surfaces with a soft brush. Remove base scale by wiping

the base with a cloth dampened with undiluted white

vinegar.

3.

Rinse with clean warm water to remove the cleaning

solution before disinfecting the tank.

To Disinfect Humidifier Base and Tank:

1.

Fill humidifier tank 1/2 full with water and 1/2

tablespoon of chlorine bleach.

2.

Let the solution stand for 20 minutes, swishing every

few minutes. Wet all surfaces.

3.

Carefully empty the tank after 20 minutes, and rinse

with warm water until you cannot detect any bleach

smell. Dry with a clean cloth or paper towel.

4.

Place filter back into tank and refill the water tank as

directed in Operating Instructions, and turn the unit on.

Holmes HCM730 Product Manual - Page 2

Please Read And Save These, Important Safety Instructions, Please Read And Save, These Important - manual

Page 2 highlights