Holmes HFH111 Product Manual - Page 2
Features - Operations, Cleaning / Maintenance, Troubleshooting, Caracteristicas Y Funcionamiento,
View all Holmes HFH111 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: 1. Read all instructions before using this heater. 2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9 m) from the front of the heater and keep them away from the sides and rear. 3. Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended. 4. Always unplug heater when not in use. 5. Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner. Discard heater, or return to authorized service facility for examination and/or repair. 6. Do not use outdoors. 7. This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate heater where it may fall into a bathtub or other water container. 8. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over. 9. To disconnect heater, turn controls to off, then remove plug from outlet. 10. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater. 11. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked. 12. A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored. 13. Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons. 14. Always plug heaters directly into a wall outlet/ receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip). 15. When unplugging, be sure to pull by the plug and not the cord. 16. If the heater will not operate, see specific instructions on Auto Safety Shut-off. 17. DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit. Doing so will void your warranty. The inside of the unit contains no user serviceable parts. All servicing should be performed by qualified personnel only. 18. Discontinue use if plug or outlet is hot. It is recommended that the outlet be replaced if plug or outlet is hot to touch. 19. The heater must not be located immediately below a socket-outlet. Do not use this heater in the immediate surroundings of a bath, a shower or a swimming pool. SAVE THESE INSTRUCTIONS THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS SAFETY FEATURE IN ANY WAY. FEATURES - OPERATIONS TECHNICAL SPECIFICATIONS • Amps: 12.5 • Wattage: 1500W (+5% -10%) • Working voltage: 120V AC/60Hz OPERATING INSTRUCTIONS 1. Carefully remove your heater from the box. Please save the carton for off-season storage. 2. Make sure the unit is in the Off position before plugging the heater into the outlet. 3. Avoid overloading your circuit by not using other high wattage appliances in the same outlet. At 1500 Watts, this unit draws 12.5 Amps. Mode Control Turn the Mode Control to the desired setting: Off Mode If you want to shut off the heater at any time of operation, turn the Mode Control to Off position. Power indicator light will remain lit until the heater is turned to Off. Fan only Setting Heater will run at fan-only operation without heat output. Low Heat The heater will run continuously at 1000W. High Heat The heater will run continuously at 1500W. Thermostat Control (for HFH111 & HFH111T ONLY) 1. Before setting the thermostat, allow heater to operate and warm up the room. As noted before, you need to turn the Thermostat Control to the highest setting to start the heater. 2. When the desired temperature comfort level is reached, lower the thermostat setting until the fan/ heater stops operating. This is done by moving the Thermostat Control counter-clockwise toward the Low setting. 3. The control will now automatically maintain the pre-set temperature level by cycling the heater ON and OFF. NOTE: To start heater operation, make sure the Thermostat Control is turned fully clockwise to the highest position. NOTE: It is normal for the heater to cycle ON and OFF as it maintains the preset temperature. To prevent the unit from cycling, you need to raise the thermostat setting. CAUTION: FRONT GRILL IS HOT WHEN UNIT IS IN OPERATION. Figure 1 for HFH110 A. Carry Handle (not shown) B. Mode Control C. Power Light A B C Figure 2 for HFH111 & HFH111T A. Thermostat Control B. Carry Handle (not shown) C. Mode Control D. Power Light AB C D CLEANING / MAINTENANCE TROUBLESHOOTING CLEANING/MAINTENANCE During Season Care: 1. Always unplug the heater before cleaning. 2. Clean the unit with a soft cloth moistened with a mild soap and water solution. 3. NEVER use abrasive or flammable solvents to clean the unit. 4. After cleaning, be sure to completely dry the unit with a cloth or towel. After Season Care: 1. Store heater in a cool, dry location. 2. It is recommended that you store the unit in its original carton. AUTO SAFETY SHUT-OFF This heater is equipped with a patented, technologically advanced, safety system that requires the user to reset the heater if there is a potential overheat situation. When a potential overheat temperature is reached, the system will automatically shut the heater off. It can only resume operation when the user resets the unit. For specific reset instructions please refer to the unit. Tip-over Shut-off (for HFH111T only): When the unit is accidentally knocked over, it will shut off. To reset, simply place the heater in an upright position on a level surface. RESET INSTRUCTIONS If your heater shuts down: 1) Turn Control to OFF. 2) Unplug the unit and wait 30 minutes. 3) Plug in and operate normally. TROUBLESHOOTING If your heater fails to operate: • Turn the heater OFF and UNPLUG THE HEATER. • Make sure the electrical outlet or circuit breaker is working. • Check for obstructions. If you find an obstruction turn the heater OFF, and unplug the unit. Carefully remove the obstruction and follow the reset instructions. • The temperature may be set too low. Turn the thermostat knob clockwise until the heater restarts. • Make sure selector is in LOW or HIGH setting. Please DO NOT attempt to open or repair the heater. If you have any questions regarding your product or would like to learn more about other Holmes® products, please contact our Consumer Service Department at 1-800-546-5637 or visit our website at www.holmesproducts.com. LEA Y GUARDE ESTAS INSTRUCCIONES DE SEGURIDAD IMPORTANTES Para reducir el riesgo de incendios, descargas eléctricas y lesiones personales al utilizar electrodomésticos, siga siempre las precauciones básicas de seguridad, incluyendo las que se mencionan a continuación: 1. Lea todas las instrucciones antes de usar este calefactor. 2. El calentador se calienta al usarlo. Para evitar quemaduras, NO toque las superficies calientes con la piel. Si existen, utilice las manijas para mover la unidad. Mantenga los materiales combustibles, como muebles, almohadones, sábanas, papeles, ropa y cortinas a por lo menos 3 pies (0,9m) de la parte delantera del calefactor y manténgalos alejados de los costados y de la parte de atrás. 3. Debe tener mucho cuidado cuando el calefactor es utilizado por, o cerca de niños o inválidos, y siempre que se deje el calefactor prendido y desatendido. 4. Siempre desenchufe el calefactor cuando no lo utilice. 5. NO utilice el calefactor si el cable o el enchufe están dañados o luego de una falla, se haya caído o haya sufrido cualquier tipo de daño. Deseche el calefactor o devuélvalo al centro de servicio autorizado para su revisión y/o reparación. 6. NO utilizar en el exterior. 7. Este calefactor no está diseñado para ser utilizado en baños, lavaderos y zonas similares de interiores. NUNCA coloque el calefactor donde pueda caerse dentro de una bañera u otro recipiente con agua. 8. No coloque el cable debajo de la alfombra. No cubra el cable con alfombras, tapetes o artículos similares. No pase el cable por debajo de muebles o electrodomésticos. Coloque el cable lejos del área de tráfico y donde no se tropiece con él. 9. Para desconectarlo, gire el control a la posición OFF, luego quite el enchufe del tomacorriente. 10. No inserte ni permita que objetos extraños penetren en la ventilación o salida de aire ya que esto puede causar un choque eléctrico o incendio, o dañar el calefactor. 11. Para evitar un posible incendio, no bloquee las entradas de aire o escape de ninguna manera. No lo use en superficies blandas, como una cama, donde las aberturas se pueden bloquear. 12. Un calefactor tiene partes calientes y que pueden producir chispas en su interior. NO lo utilice en áreas donde se utiliza o se guarda gasolina, pintura o líquidos inflamables. 13. Utilice este calefactor sólo como se describe en este manual. Cualquier otro uso no recomendado por el fabricante puede provocar incendios, descargas eléctricas o lesiones a personas. 14. Siempre conecte el calefactor directamente a un tomacorriente de pared. Nunca lo use con un cable de extensión o con un tomacorriente múltiple. 15. Al desenchufarlo, asegúrese de tirar del enchufe y no del cable. 16. Si el calefactor no funciona, vea las instrucciones específicas del apagado automático de seguridad. 17. NO intente reparar o ajustar ninguna función eléctrica o mecánica de esta unidad. El hacerlo invalidará la garantía. La unidad no contiene partes reparables por el usuario. Toda reparación debe ser realizada únicamente por personal calificado. 18. Deje de usarlo si el cable o el enchufe se calienta. Se recomienda que reemplace el tomacorriente si el enchufe o el tomacorriente se calienta. 19. El calefactor no se debe localizar inmediatamente debajo de un tomacorriente. No use este calefactor en áreas cercanas a un baño, una ducha o una piscina. CONSERVE ESTAS INSTRUCCIONES ESTE PRODUCTO TIENE UN ENCHUFE POLARIZADO (una hoja es más ancha que la otra). A fin de disminuir el riesgo de descarga eléctrica, este enchufe está diseñado para insertarse en un tomacorriente polarizado en un solo sentido. Si el enchufe no entra completamente en el tomacorriente, inviértalo. Si aun así no entra, llame a un electricista calificado para instalar un tomacorriente apropiado. NO MODIFIQUE EL ENCHUFE NI ANULE ESTA FUNCION DE SEGURIDAD DE NINGUNA MANERA. HFH110/111/111T/WF110_12ESM1.indd 2 CARACTERISTICAS Y FUNCIONAMIENTO ESPECIFICACIONES TECNICAS • Amperes: 12,5 • Potencia: 1500 W (+5% -10%) • Voltaje de funcionamiento: 120v CA/60Hz INSTRUCCIONES DE USO 1. Saque cuidadosamente el calefactor de la caja. Conserve la caja para guardarlo en el verano. 2. Asegúrese de que esté en la posición Apagado antes de enchufarlo en el tomacorriente. 3. Evite sobrecargar el circuito eléctrico evitando utilizar otro aparato de alta potencia en el mismo tomacorriente. A 1500 Vatios, esta unidad consume 12,5 Amperes. Control de modo Con el Control de modo, seleccione la configuración deseada: Modo Apagado Si desea apagar el calefactor en cualquier momento, gire el Control de modo hasta la posición APAGADO. La luz del indicador de encendido permanecerá encendida hasta que se configure el calefactor en Apagado. Configuración Sólo ventilador El calefactor funcionará en la configuración Sólo ventilador sin emitir calor. Calor Bajo El calefactor funcionará continuamente a 1000W. Calor Alto El calefactor funcionará continuamente a 1500W. Control de termostato (solo para la HFH111 & HFH111T) 1. Antes de configurar el termostato, permita que el calefactor caliente la habitación. Como se indicó anteriormente, para encender el calefactor, debe girar el control del termostato hasta alcanzar el nivel más Alto. 2. Al alcanzar la temperatura deseada, disminuya el ajuste del termostato hasta que el ventilador/ calefactor deje de funcionar. Esto se hace moviendo el control del termostato en sentido contrario al de las agujas del reloj hasta el ajuste Baja que es el menor. 3. El control se mantendrá ahora dentro del nivel precalibrado, determinando el arranque y detención (ON y OFF) del calefactor. NOTA: Para iniciar la operación del calefactor, asegúrese de que el control del termostato se gire completamente en el sentido de las agujas del reloj en la posición más Alta. NOTA: Es normal que el calefactor se encienda y apague intermitentemente mientras mantiene la temperatura seleccionada. Para evitar que la unidad se encienda y apague, debe aumentar el ajuste del termostato. PRECAUCIÓN: LA REJILLA FRONTAL SE CALIENTA CUANDO LA UNIDAD ESTÁ EN FUNCIONAMIENTO. Figura 1 solo para la HFH110 A. Manija de Transporte (no se muestra) B. Control de Modo C. Luz de Encendido A B C Figura 2 solo para la HFH111 & HFH111T A. Control del Thermostato B. Manija de Transporte (no se muestra) C. Control de Modo D. Luz de Encendido AB C D LIMPIE ZA Y MANTENIMIENTO SI SU CALEFACTOR NO FUNCIONA LIMPIEZA / MANTENIMIENTO Durante la temporada: 1. Siempre desenchufe el calefactor antes de limpiarlo. 2. Limpie la unidad con un paño suave humedecido en una solución suave de agua y jabón. 3. NUNCA utilice solventes abrasivos o inflamables para limpiar la unidad. 4. Luego de limpiarla, asegúrese de secar completamente la unidad con un trapo o toalla. Después de la temporada: 1. Guarde el calefactor en un lugar frío y seco. 2. Se recomienda guardar la unidad en su embalaje original. APAGADO AUTOMÁTICO DE SEGURIDAD Este calefactor está equipado con un sistema de seguridad patentado, de tecnología avanzada que requiere que el usuario reinicie el calefactor en caso de un sobrecalentamiento potencial. Cuando se alcanza una temperatura de un posible recalentamiento, el sistema apagará automáticamente el calefactor. Volverá a funcionar únicamente cuando el usuario prenda de nuevo la unidad. Vea la unidad para instrucciones específicas de reinicio. Apagado de Inclinación (solo para HFH111T): Cuando la unidad se cae accidentalmente, se apaga. Para reiniciarla, simplemente coloque el calefactor verticalmente sobre una superficie nivelada. INSTRUCCIONES VOLVER A ENCENDER Si la unidad se apaga: 1) GIRE el Control a APAGADO. 2) Desenchufe la unidad y espere 30 minutos. 3) Enchufela y vuélvala a operar normalmente. DIAGNOSTICO DE PROBLEMAS Si su calefactor no funciona: • APAGUE el calefactor y DESENCHÚFELO. • Asegúrese de que el tomacorriente o llave térmica funcionen correctamente. • Verifique que no haya ninguna obstrucción. Si encuentra una obstrucción, apague el calefactor, y DESENCHUFELO. Quite cuidadosamente la obstrucción y siga el procedimiento para reiniciar la unidad. • El termostato puede estar ajustado demasiado bajo. Gire la perilla del termostato en sentido de las agujas del reloj hasta que comience a calentar nuevamente. • Verifique que el Control de Modo esté en la posición LOW o HIGH. NO intente abrir o reparar el calefactor. If you have any questions regarding your product or would like to learn more about other Holmes® products, please contact our Consumer Service Department at 1-800-546-5637 or visit our website at www.holmesproducts.com. 11/17/11 3:39 PM